Sharan EPC and Engine light on

[charbel89]

Hi,

I have a sharan 2.0, X Reg.


EPC light come one every now and then espcially after driving the car for a bit then stopping and then moving on, I start to get the EPC light.

I also got the Engine Managment light come on.

I ran Vag-Com and there were few error, I cleared all but the belwo one will not go away:

17852 - Potentiometer for EGR (G212): Implausible Signal P1444 - 35-00 - -

I have not driven the car since I clear the codes to confirm if any of the other codes will return.


Any ideas what this could be?


Thanks

Regards


Charbel

[charbel89]

Three questions:

1- How do I get my car recoded? (my understanding is that this eliminates the need to reenter the security code if power was lost). The radio has been replaced with same original VW version).

2- The engine management light is now always on due to :

16497 - Intake Air Temp. Sensor (G42): Signal too High
P0113 - 35-10 - - - Intermittent

The MAF is about 2 years old.


3- As in my first post, when I start the car after a small journey the EPC light shows up when accelerating. It shows up for a bit and then goes away. (I have previously replaced the brake light switch but no change). Could this be related to:

17852 - Potentiometer for EGR (G212): Implausible Signal
P1444 - 35-00 - -

Here is the scan:

VAG-COM Version: Release 409.1-S


Chassis Type: 7M - VW Sharan
Scan: 01,02,03,08,09,15,16,17,18,19,29,36,37,39,45,46,55 ,56

-------------------------------------------------------------------------------
Address 01: Engine
Controller: 06A 906 032 AL
Component: 2.0l R4/2V AG4 3501
Coding: 00003
Shop #: WSC 00000
2 Faults Found:
17852 - Potentiometer for EGR (G212): Implausible Signal
P1444 - 35-00 - -
16497 - Intake Air Temp. Sensor (G42): Signal too High
P0113 - 35-10 - - - Intermittent
Readiness: 0010 1001

-------------------------------------------------------------------------------
Address 02: Auto Trans
Controller: 099 927 733 AN
Component: AG4 Getriebe 099 4774
Coding: 00000
Shop #: WSC 00000
No fault code found.

-------------------------------------------------------------------------------
Address 03: ABS Brakes
Controller: 1J0 907 379 P
Component: ABS 20 IE CAN 0001
Coding: 12502
Shop #: WSC 00020
No fault code found.

-------------------------------------------------------------------------------
Address 08: Auto HVAC
Controller: 7M3 907 049
Component: Klimabetaetigung 0202
Coding: 0000000
Shop #: WSC 00000
No fault code found.

-------------------------------------------------------------------------------
Address 09: Cent. Elect.
Controller: 7M3 962 258 E
Component: Multifunkt.Einheit 0001
Coding: 00005
Shop #: WSC 00020
No fault code found.

-------------------------------------------------------------------------------
Skipping Address 15-Airbags

-------------------------------------------------------------------------------
Address 17: Instruments
Controller: 7M3 920 920 MX
Component: KOMBIINSTRUMENT VDO V67
Coding: 09403
Shop #: WSC 00096
No fault code found.

-------------------------------------------------------------------------------
Address 19: CAN Gateway
Controller: 6N0 909 901
Component: Gateway K<->CAN 0001
Coding: 00006
Shop #: WSC 00096
No fault code found.

-------------------------------------------------------------------------------
Address 56: Radio
Controller: 1J0 035 152 E
Component: Radio GRO 0001
Coding: 00000
Shop #: WSC 00000
1 Fault Found:
01044 - Control Module Incorrectly Coded
35-00 - -

End --------------------------------------------------------------------------------------------------

Thanks a lot.

Charbel

[jskak]

Check your wiring to the plug at the MAFS. I've seen them break where the wiring joins to the main loom.