A6 C6 VCDS Changes - Post & Pre Facelift

[MFGF]

Pre-facelift Cars - 04 - 08 plate

1. Confirmation on Lock
[Select]
[46 - Central Conv]
[Coding - 07]
+2048 to your existing coding (example - original code is 0008443 + 2048 = 0010491)
[Do it!]

2. MMI High Hidden Menu
[Select]
[07 - Control Head]
[Adaption - 10]
Drop-down Menu
[Select - Service Menu]
Change 'New Value'to 1
[Test]
[Save]

Drop-down Menu
[Select - MMI System Retstart]
Change 'New Value' to 1
[Test]
[Save]
*MMI will now restart*
[Done, Go Back]

3. Battery Meter
After MMI restart and Hidden Menu enable - press Radio then hold in Setup + Car for a few seconds (it might take a few times to get timing correct)
[Select] DIAG SETTINGS
[Select] Car Menus Maske
[Select] Battery Level
Scroll to Accept Changes
Press RETURN 3 times
Restart MMI using Setup + MMI Control Knob + Upper Left Inner Key - release


4. Visual Parking Aid - if supported
[Select]
[76 - Park Assist]
[Coding - 07]
Change second digit to '2'
Example - Original code is 0001106 ... New code is 0201106
[Do it!]
Restart MMI and select reverse

5. Passenger Mirror Dip on Reverse - if supported
[Select]
[52 - Door Elec Pass.]
[07 - Coding]
Add +128 to original coding
Example - original code is 0002682 ... New code is 0002810
[Do it!]
Select LHS mirror on control and select reverse - mirror will dip if correct hardware is fitted

6. MMI High Startup Screen
[Select]
[07 - Control Head]
[07- Coding]
Look for the 3rd digit and change this to your preference as below
xx0xxxx = A6
xx1xxxx = S6
xx3xxxx = RS6
[Do it!]
Now go into:
[10 - Adaption]
Drop-down Menu
[Select - MMI System Retstart]
Change 'New Value' to 1
[Test]
[Save]
*MMI will now restart*
[Done, Go Back]

7. Disable Seatbelt Warning
[Select]
[17 - Instrument Cluster]
[07 - Coding]
Look for the 6th digit and change this to your preference as below
xxxxx0x = No Seatbelt Warning
xxxxx1x = Seatbelt Warning (EU-NCAP)
xxxxx2x = Seatbelt Warning (NAR Old)
xxxxx3x = Seatbelt Warning (NAR New)
xxxxx4x = Seatbelt Warning (EU-NCAP incl. Passenger)
xxxxx5x = Seatbelt warning (NAR Old incl. Passenger)
xxxxx6x = Seatbelt Warning (NAR New incl. Passenger)
[Do it!]
Turn ignition off and on

NB . 2, 3, 5 & 6 are related to North America.

8. Bluetooth Module Voice Control - If your BT module supports this change
[Select]
[77 - Telephone]
[07 - Coding]
Look for the 6th digit in your current coding and change this to your prefered voice language
00x0x00 = Voice Control Off
00x0x10 = German
00x0x20 = English (UK)
00x0x30 = French
00x0x40 = Italian
00x0x50 = Spanish
00x0x60 = Spanish (USA)
00x0x70 = English (USA)
00x0x80 = French (Canada)
00x0x90 = Speaker dependant voice selection
[Do it!]

Now restart your MMI
[Select]
[07 - Control Head]
[10 - Adaption]
Drop-down Menu
[Select - MMI System Retstart]
Change 'New Value' to 1
[Test]
[Save]
*MMI will now restart*
[Done, Go Back]

9 - Scandanavian DRL (rear tail lights on with front DRL)
[Select]
[09 - Cent Conv]
[Coding - 07]
Change the last digit in the coding string to '2'
Example - 0xxxxx2
[Do It!]


10. Changing radio source by pressing RADIO

[Select]
[07 - Control Head]
[Adaption - 10]
Additional MMI Options
Add 4 to your existing code (Frequency/Source Change via Function Button Active)
[Test]
[Save]


Facelift Cars - '58 plate onwards

1. Enabling Gauge Test/Needle Sweep
[Select]
[17 - Instruments]
[Coding - 07]
[Long Coding Helper]
Click on the second byte in the list.
Check the box for "Gauge Test/Needle Sweep active"
[Do It!]

2. Hidden menu in 3G MMI
[Select]
[5F - Information Electr.]
[Adaptation - 10]
Choose Channel 6
change value from 0 to 1
[Save]
[Done]

3. Enabling VIM (Video in Motion)
[Select]
[Control Module 5f]
[Advanced ID - 1A]
Make a note of the serial number and decode using MMI VIMGen
[Security Access - 16]
Enter the code generated above
[Do it!]
[Adaptation - 10]
Choose Channel 48
change value from 0 to 255
[Save]
[Done]
Restart MMI

4. Enable Battery Meter once #2 has been completed
Hold in CAR + SETUP
car
carextdevicelist
check "Battery"
return
carmenuoperation
set "Battery" to 5
return
Restart MMI

5. Enable Bluetooth on MMI 3G
[Select]
[Control Module 5f]
[Adaption - 10]
Channel 06
New Value = 1
Test, Save, Done.

Now go into the Hidden Menu, see 2. Hidden menu in 3G MMI
Diagnose>Settings>Tel Settings Misc
Change the available options to - [no WLAN/no NAD/BT/HFP] 4/16
Restart MMI (Hold in SETUP + Centre MMI Knob + Upper Right Inner Key]

[Select]
[Control Module 5F]
[Adaption - 10]
Channel 17
New Value = 1
Test, Save, Done.
Restart MMI (Hold in SETUP + Centre MMI Knob + Upper Right Inner Key]

If you have Nav fitted, the microphone will be present, if no Nav is fitted then you need to purchase microphone pack 4L1 (or 4L2) 035 711 G

6. Enable AMI (Audi Music Interface) on MMI 3G (after fitting the hardware)

[Select]
[Control Module 5F]
[Adaption - 10]
Channel 6
New Value = 1
Restart MMI (Hold in SETUP + Centre MMI Knob + Upper Right Inner Key]
Go into hidden menu, hold in CAR + SETUP ... WARNING DO NOT CHANGE ANY VALUES YOU DON'T KNOW OR ELSE BAD BAD THINGS MAY HAPPEN ;)
Diagnosis -> Settings -> Audi Music Interface (AMI) set to 7/8
Press RETURN and come out of the hidden menu.
Restart MMI (Hold in SETUP + Centre MMI Knob + Upper Right Inner Key]
Press MEDIA, Source and test the AMI.

7. Visual Parking Aid - if supported
[Select]
[76 - Park Assist]
[Coding - 07]
Change second digit to '2'
Example - Original code is 0001106 ... New code is 0201106
[Do it!]
Restart MMI and select reverse

8. Enabling Lap Timer/Boost Guage/Oil Temp
[Select]
[17 - Instruments]
[Coding - 07]
[Long Coding Helper]
Check the box for "Lap Timer active"
[Do It!]

9. Enable Rear DRL (Scandinavian Lights)
[Select]
[09 - Cent Elec]
[Coding - 07]
Change the 7th digit (ie the last one) to 2
[Do It!]

10. Enable Passenger Mirror Dipping
[Select]
[52 - Passenger Door]
[Coding - 07]
Byte 4, bit 3 - Position memory for reverse gear dipping active
Tick the box
[Do It!]
Test by turning ignition off and then on, select the passenger side on the adjustment switch and select reverse.

[enry68]

If it is of your interest, my A6 is MY2010 and my 5F codification is this:

Address 5F: Information Electr. (J794) Labels: Redir Fail!
Part No SW: 4E0 035 666 C HW: 4E0 035 666 C
Component: H-BN-EU H45 0047
Revision: -------- Serial number: xxxxxxxxxxxxxxxxxxx
Coding: 010100010002E3ED01000715EF6300030001
Shop #: WSC 02391 823 56573
VCID: xxxxxxxxxxxxxxxx
Part No: 8R0 060 884 J
Component: EUR 2010 1005
Part No SW: 4F0 919 604 HW: 4F0 919 604
Component: DU7 High H43 0306
Part No SW: 4F0 910 609 E HW: 4F1 919 611 S
Component: Bedienteil MM H01 0060
No fault code found.

I hope this can help tou,
Enrico.

[MFGF]

Thanks! It looks like your 5F module is a later revision than mine - yours is 4E0 035 666 C and mine is 4E0 035 666 B

I don't get any issues with the 5F at all - just this error reported in VCDS. I only have the car for another two months, so I guess it will never get resolved.

Cheers!

MF.

[enry68]

Can You gentily post all the ECUs codification with VCDS using the function scanner ?

I've an A6 Avant TDI 2.0 170cv as you and I wish to add the functionality: AHA (Audi hill Assist). i think it is a codification of the ABS ECU (addr. 03) but i don't know which are the right bits ...

I think that in UK, AUDI enable this feature automatically and I whish to add it on my car.

Can You help me please ?
Enrico.

[MFGF]

None of the A6 4Fs over here in the UK have hill hold as far as I know - I have never seen it offered as an option.

I can happily post the coding of my ABS module, but it will not really help you I imagine - my car does not have hill hold.

It is now a standard feature on the new 4G A6s, but they are a totally different car.

MF.


Sent from my iPad using Tapatalk

[enry68]

Many thanks MF,
I know that A4 (B8/8K chassis) and some A6 (4F-C6 restyle, like mine) has this option anabled. So I think that it is only a different codification of the ABS module. Now if your A6 does not has it, it is not necessary that You post your ABS codification.

The same thing is for some features anabled into the 5F module. For example,did your audio system has some DSP effects ? Your audio system is composed by 8, 10 o more speakers ?

Thanks again,
Enrico.

[andye26]

Hi
MFGF
Did you get 01043 - Control Module; Incorrect Software Version resolved?

There is a way to clear this fault you need to read
[Adaptation - 10] -> Channel 15

Value should be 0 count number is important
Take your count number and do some sums.
if count is 2164 adapatation value is worked out like this
2164 xor 51666 = 49574
49574 is the adaptation value....51666 is always the same

Regards
Andy

[MFGF]

Hi
MFGF
Did you get 01043 - Control Module; Incorrect Software Version resolved?

There is a way to clear this fault you need to read
[Adaptation - 10] -> Channel 15

Value should be 0 count number is important
Take your count number and do some sums.
if count is 2164 adapatation value is worked out like this
2164 xor 51666 = 49574
49574 is the adaptation value....51666 is always the same

Regards
Andy

Hi Andy,

Ok. This is officially weird. I just went out to the car armed with this information and my VCDS on my laptop. When I scanned the car before starting any changes, it reported no faults across the board! Specifically, the results for the 5f module looked like this:

-------------------------------------------------------------------------------
Address 5F: Information Electr. (J794) Labels: 4E0-035-6xx-5F.clb
Part No SW: 4E0 035 666 D HW: 4E0 035 666
Component: H-BN-EU H64 0143
Revision: -------- Serial number: 345BY097545942
Coding: 010101000102C3ED01000315EF6300030001
Shop #: WSC 00778 210 97003
VCID: 2756F15056F635B
Subsystem 1 - Part No: 8R0 060 884 R
Component: EUR 2010 1107
Subsystem 2 - Part No SW: 4F0 919 604 HW: 4F0 919 604
Component: DU7 High H43 0306
Subsystem 3 - Part No SW: 4F0 910 609 E HW: 4F2 919 611 M
Component: Bedienteil MM H01 0060
No fault code found.

This scan result looks entirely different to the way it used to!

I was intrigued, so I went to look at the values in Adaptation channel 15. My count number is 10420, but the stored adaptation value is 0. According to the calculation, the stored adaptation should be 55702. No errors are reported, though. Very weird!!!

The car was in at my dealer for service last week - I wonder if any kind of software update was done which may have fixed the issue? I checked my installed version, and it reports HNav_EU_K0031_3_D1

Because no error is being reported, I have not changed the adaptation value. I will keep an eye on it over the next few weeks and see if the error returns.

The only other change I can think of is the version of VCDS - I am now on the following after the latest update:

VCDS Version: Release 11.11.2 (x64)
Data version: 20120126

I now have a labels file for the 5f, whereas there wasn't one available back in February 2010 when I first recorded the scan in VCDS 908.1. I don't see how this could have had any impact on the error, though.

Cheers!

MF.

[andye26]

Hi
Im not sure but I think the adaptation channel reverts to 0 after you enter your value
My incorrect software version only appeared after I added the battery meter so think it is some sort of checksum for mmi
Did all you vcds tweeks stay after your visit to the dealer?

Andy

PS when I entered my new adaptation value the fault code cleared without me having to clear fault codes

[MFGF]

Hi
Im not sure but I think the adaptation channel reverts to 0 after you enter your value
My incorrect software version only appeared after I added the battery meter so think it is some sort of checksum for mmi
Did all you vcds tweeks stay after your visit to the dealer?

Andy

PS when I entered my new adaptation value the fault code cleared without me having to clear fault codes

I see! It looks like there is no need for me to do anything at this point, then. It's puzzling that the fault disappeared of its own accord, though.

I always reset all modules back to standard coding and adaptation values before the car goes in to the dealer. I reckon the tech servicing my car has enough pressure to do the job in a fixed time without getting distracted by non-standard module coding being flagged up. I only have the car for eight weeks, so I will probably leave the coding as standard now so I don't have to reset it all when the car goes.

Thanks for the useful info!

MF.


Sent from my iPad using Tapatalk HD

[Guest 2]

Original post now updated with Pre-facelift changes 20/7.

Also stickied for more coverage.

If any have been missed please reply and these can be added.

[c4a5er]

I don't see adding 'Lap timer' anywhere so far so you can add that.

address 17 instruments

use long code helper

change byte 1 bit 3 to make lap timer active.

It then becomes an option in the DIS screen, the oil temperature display is probably the most useful but there is a timer and a gimmicky boost gauge as well.

[Guest 2]

Thanks will add soon ;)

[Blackavant]

Has anyone managed to enable ambient lighting on the faclift 2009+ models?

I've tried but have no ability to adjust the Byte / Bit in the long code helper, nothing is shown.

I got this to work easily on my 06 Plate A6, but no luck on my 10 plate.

[MFGF]

Has anyone managed to enable ambient lighting on the faclift 2009+ models?

I've tried but have no ability to adjust the Byte / Bit in the long code helper, nothing is shown.

I got this to work easily on my 06 Plate A6, but no luck on my 10 plate.

My last C6 facelift (2009 Le Mans) had the Ambient Lighting pack fitted as standard. I still have the scans from the car. Which module do you need the coding for? You could try copying mine to see if it works?

Here is the last scan I took in March 2012:

VCDS Version: Release 11.11.2 (x64)
Data version: 20120126
Thursday,01,March,2012,09:55:17:07948
Chassis Type: 4F0
Scan: 01 03 05 08 09 15 16 17 19 42 46 4F 52 53 55 56 5F 62 72 76

VIN: WAUZZZ4F09N055366 Mileage: 90000km/55923miles
01-Engine -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
05-Acc/Start Auth. -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
46-Central Conv. -- Status: OK 0000
4F-Centr. Electr. II -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
53-Parking Brake -- Status: OK 0000
55-Xenon Range -- Status: OK 0000
56-Radio -- Status: OK 0000
5F-Information Electr. -- Status: OK 0000
62-Door, Rear Left -- Status: OK 0000
72-Door, Rear Right -- Status: OK 0000
76-Park Assist -- Status: OK 0000

-------------------------------------------------------------------------------
Address 01: Engine (J623-CAHA) Labels: 03L-906-022-CAG.clb
Part No SW: 03L 906 022 FG HW: 03L 906 022 FG
Component: R4 2,0L EDC H01 4397
Revision: 11H01--- Serial number:
Coding: 0105002C18072118
Shop #: WSC 02325 785 00200
ASAM Dataset: EV_ECM20TDI03L906022FG A01006
ROD: EV_ECM20TDI03L906022FG.rod
VCID: 6FE6D970B6862DB
No fault code found.
Readiness: 0 0 0 0 0
-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 4F0-910-517.lbl
Part No SW: 4F0 910 517 AK HW: 4F0 614 517 AT
Component: ESP8 front H03 0060
Revision: 00000000 Serial number: 00000000000000
Coding: 0020859
Shop #: WSC 02325 785 00200
VCID: 6DDAC378748ADFB
No fault code found.
-------------------------------------------------------------------------------
Address 05: Acc/Start Auth. Labels: 4F0-910-852.clb
Part No SW: 4F0 910 852 B HW: 4F0 905 852 D
Component: FBSAUDIC6 ELV H05 0100
Revision: 00H05000 Serial number: 10602601299048
Coding: 0000017
Shop #: WSC 02324 785 00200
VCID: 254AFB58ECFA27B
Part No: 4F0 910 132 D
Component: FBSAUDIC6 EZS H03 0020
Part No: 4F0 910 220 D
Component: FBSAUDIC6 IDG H01 0040
No fault code found.
-------------------------------------------------------------------------------
Address 08: Auto HVAC Labels: 4F0-910-043.lbl
Part No SW: 4F0 910 043 B HW: 4F2 820 043 AA
Component: KLIMABETAETIGUNGH30 0080
Revision: 00000074 Serial number: 00000030430038
Coding: 0001044
Shop #: WSC 02325 785 00200
VCID: 1D3AD3B8C4AAEFB
No fault code found.
-------------------------------------------------------------------------------
Address 09: Cent. Elect. Labels: 4F0-910-279.lbl
Part No SW: 4F0 910 279 N HW: 4F0 907 279
Component: ILM Fahrer H22 0320
Revision: 00000000 Serial number: 4F0907279
Coding: 0013121
Shop #: WSC 02256 785 00200
VCID: 346C161C57204E3
Subsystem 1 - Part No: 4F2 910 113 C Labels: 1KX-955-119.CLB
Component: Wischer AudiC6 H10 0040
Coding: 00056595
Shop #: WSC 02256
Subsystem 2 - Part No: 8K0 910 557 Labels: 8K0-955-559.CLB
Component: REGENLICHTSENSORH04 0003
Coding: 00146221
Shop #: WSC 02256
No fault code found.
-------------------------------------------------------------------------------
Address 15: Airbags (J234) Labels: 4F0-910-655-10.clb
Part No SW: 4F0 910 655 L HW: 4F0 959 655 E
Component: Airbag AU1042 H06 0090
Revision: -------- Serial number: 003CH004D55G
Coding: 30314236303630303033554A305234463053
Shop #: WSC 02324 785 00200
ASAM Dataset: EV_Airba10AURB4 001001
ROD: EV_Airba10AURB4.rod
VCID: 30641A0C6B38723
Crash sensor for side airbag; driver side:
Serial number: 3574SRB400008C651AFH
Crash sensor for side airbag; passenger side:
Serial number: 3584SRB400008C5C819G
Crash sensor for side airbag; rear driver side:
Serial number: 35152RB402T85LSIV3L9
Crash sensor for side airbag; rear passenger side:
Serial number: 35252RB402B85LSJ3BA5
Crash sensor for front airbag; driver side:
Serial number: 3554NRB400004B2A387+
Crash sensor for front airbag; passenger side:
Serial number: 3564NRB400004B32BAFA
No fault code found.
-------------------------------------------------------------------------------
Address 16: Steering wheel Labels: 4F0-910-549.lbl
Part No SW: 4F0 910 549 A HW: 4F0 953 549 D
Component: J0527 0530
Revision: 00H05000 Serial number: 90055090630424
Coding: 0102041
Shop #: WSC 02324 785 00200
VCID: 2756F15096F635B
Part No: XXXXXXXXXXX
Component: E0221 H02 0030
No fault code found.
-------------------------------------------------------------------------------
Address 17: Instruments (J285) Labels: 4F0-920-xxx-17.clb
Part No SW: 4F0 920 983 B HW: 4F0 920 983 B
Component: KOMBIINSTR. H06 0135
Revision: 00100000 Serial number: AE944MT29
Coding: 2F74080502002600010400
Shop #: WSC 02391 823 56573
VCID: 2B5E0D604A1E11B
No fault code found.
-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533) Labels: 4F0-907-468.clb
Part No SW: 4F0 907 468 K HW: 4F0 907 468 F
Component: GW-BEM 4CAN-M H06 0025
Revision: 4LA80024 Serial number: 2400L09330837F
Coding: 000303
Shop #: WSC 02391 823 56573
VCID: 377621108656A5B
Subsystem 1 - Part No SW: 8K0 915 181 C HW: 8K0 915 181 C
Component: J367-BDM H07 0107
No fault code found.
-------------------------------------------------------------------------------
Address 42: Door Elect, Driver (J386) Labels: 4F0-959-793.clb
Part No SW: 4F0 959 793 R HW: 8K0 959 793 D
Component: TSG FA H11 0250
Revision: Serial number: 0000100888916
Coding: 011F06204041410001
Shop #: WSC 02391 823 56573
VCID: 46885CD4F1BCCC3
No fault code found.
-------------------------------------------------------------------------------
Address 46: Central Conv. Labels: 4F0-910-289.lbl
Part No SW: 4F0 910 289 N HW: 4F0 907 289 N
Component: Komfortgeraet H28 0240
Revision: 02400028 Serial number: 01177736730000
Coding: 0139771
Shop #: WSC 02256 785 00200
VCID: 356A2B185C5A57B
Part No: 1K0 951 605 C
Component: LIN BACKUP HORN H03 1301
Part No: 4F0 910 177
Component: Innenraumueberw.H01 0020
No fault code found.
-------------------------------------------------------------------------------
Address 4F: Centr. Electr. II Labels: 4F0-910-280.lbl
Part No SW: 4F0 910 280 HW: 4F0 907 280 A
Component: ILM Beifahrer H13 0100
Revision: Serial number: 00000000623181
Coding: 0001104
Shop #: WSC 02324 785 00200
VCID: DEB814B4092C343
No fault code found.
-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. (J387) Labels: 4F0-959-792.clb
Part No SW: 4F0 959 792 R HW: 8K0 959 792 D
Component: TSG BF H11 0250
Revision: Serial number: 0000100894992
Coding: 011F06204041410001
Shop #: WSC 02391 823 56573
VCID: 458A5BD8CCBAC7B
No fault code found.
-------------------------------------------------------------------------------
Address 53: Parking Brake Labels: 4F0-910-801.clb
Part No SW: 4F0 910 801 D HW: 4F0 907 801 B
Component: EPB CEFC0090 H05 0090
Revision: --H05---
Coding: 0000111
Shop #: WSC 02145 785 00200
VCID: 2142EF48F8D2CBB
No fault code found.
-------------------------------------------------------------------------------
Address 55: Xenon Range Labels: 8P0-907-357.lbl
Part No: 8P0 907 357 H
Component: Dynamische LWR H02 0010
Revision: 00000001 Serial number:
Coding: 0000003
Shop #: WSC 02325 785 00200
VCID: 3F8649306E669DB
No fault code found.
-------------------------------------------------------------------------------
Address 56: Radio (R) Labels: Redir Fail!
Part No SW: 4F0 035 056 J HW: 4F0 035 056
Component: Radio U STD H45 0052
Revision: AB001007 Serial number: 342D.097595266
Coding: 010003020100000000
Shop #: WSC 00778 210 81005
VCID: 2756F15056F635B
No fault code found.
-------------------------------------------------------------------------------
Address 5F: Information Electr. (J794) Labels: 4E0-035-6xx-5F.clb
Part No SW: 4E0 035 666 D HW: 4E0 035 666
Component: H-BN-EU H64 0143
Revision: -------- Serial number: 345BY097545942
Coding: 010101000102C3ED01000315EF6300030001
Shop #: WSC 00778 210 97003
VCID: 2756F15056F635B
Subsystem 1 - Part No: 8R0 060 884 R
Component: EUR 2010 1107
Subsystem 2 - Part No SW: 4F0 919 604 HW: 4F0 919 604
Component: DU7 High H43 0306
Subsystem 3 - Part No SW: 4F0 910 609 E HW: 4F2 919 611 M
Component: Bedienteil MM H01 0060
No fault code found.
-------------------------------------------------------------------------------
Address 62: Door, Rear Left (J388) Labels: 4F0-959-795.clb
Part No SW: 4F0 959 795 M HW: 8K0 959 795 B
Component: TSG HL H10 0251
Revision: Serial number: 0000100898708
Coding: 010E04204041220001
Shop #: WSC 02391 823 56573
VCID: 438E45C0C28EF9B
No fault code found.
-------------------------------------------------------------------------------
Address 72: Door, Rear Right (J389) Labels: 4F0-959-795.clb
Part No SW: 4F0 959 795 M HW: 8K0 959 795 B
Component: TSG HR H10 0251
Revision: Serial number: 0000100906585
Coding: 010E04204041220001
Shop #: WSC 02391 823 56573
VCID: 438E45C0C28EF9B
No fault code found.
-------------------------------------------------------------------------------
Address 76: Park Assist Labels: 4Fx-910-283.lbl
Part No SW: 4L0 910 283 C HW: 4L0 919 283 C
Component: Parkhilfe 8-Kan H02 0500
Revision: 00H02000 Serial number: 12630908904181
Coding: 0200006
Shop #: WSC 02324 785 00200
VCID: 2A50086485E4083
No fault code found.
End ---------------------------------------------------------------------


Cheers!

MF.

[gupsterg]

I don't see adding 'Lap timer' anywhere so far so you can add that.

address 17 instruments

use long code helper

change byte 1 bit 3 to make lap timer active.

It then becomes an option in the DIS screen, the oil temperature display is probably the most useful but there is a timer and a gimmicky boost gauge as well.

AFAIK only work on face lift cars as tried this when got my VCDS in Jan on mine and did not work :Blush2:

[MFGF]

AFAIK only work on face lift cars as tried this when got my VCDS in Jan on mine and did not work :Blush2:


Yep - only applicable to facelift cars with the new-design cluster.

MF.

[furfurfur]

The mods I have done that aren't mentioned already here (pre facelift):

1. Changed the MMI boot/standby screen from the boring standard one to the RS6 one.

Control Head - Coding - Change 3rd digit (..X....) from 0 to 3. 0 is A6, 1 is S6 and 3 is RS6. This also makes the car feel much faster! ;)

2. Disabled seatbelt warning. In my circumstances (no kids in car) I like to have full control and in the rare event it used to warn me, it was due to pressure from something on the passenger seat that wasn't actually a passenger. I tend to know if I am wearing my seatbelt or not!

Instrument Cluster - Coding - 6th digit (.....X.)

0 = No Seatbelt Warning
1 = Seatbelt Warning (EU-NCAP)
2 = Seatbelt Warning (NAR Old)
3 = Seatbelt Warning (NAR New)
4 = Seatbelt Warning (EU-NCAP incl. Passenger)
5 = Seatbelt warning (NAR Old incl. Passenger)
6 = Seatbelt Warning (NAR New incl. Passenger)

[Guest 2]

Will add those to the original post .. Ta! ;)

Edit - Now added.

[gupsterg]

Hi peeps :) ...

I was going to add voice control at some point to my car...

As a test I enabled voice control in the bluetooth module...

Ref link:- Audi A6 (4F) Telephone Preparation - Ross-Tech Wiki (http://wiki.ross-tech.com/wiki/index.php?title=Audi_A6_%284F%29_Telephone_Prepara tion&redirect=no)


[77] - Telephone

00x0x?0: Voice Control Language

2 = English (United Kingdom)



On Link:- Ross-Tech 4F wiki (http://wiki.ross-tech.com/wiki/index.php/Audi_A6/S6/RS6/allroad_%284F%29) they show it will work for BT modules with labels 4E0-910-336 & 4F1-910-336 ... but not 4E0-910-333...

[MFGF]

Thanks Gup. Hopefully Chris will spot this and add it to the beginning of the thread... :)

[Guest 2]

Mark, the original post is still yours so you can edit it in but I'll do it now ;)

[MFGF]

Oh! Stupid me! I should have realised that. Thanks Chris - next time I will do the honours :)


Sent from my iPad using Tapatalk

[Igloo]

Hi guys,

I have the facelift cluster on my pre facelift. Will the needle sweep work with that setup?

[MFGF]

Hi guys,

I have the facelift cluster on my pre facelift. Will the needle sweep work with that setup?

I assume so. The only way to be sure is to plug in and see if it's an option.

MF.

[humphrey999]

Hi guys,

I have the facelift cluster on my pre facelift. Will the needle sweep work with that setup?

Yes it will, I have the same setup and needle sweep is activated.

[techfreak]

Instead of beep on lock can hazard flash on lock be enabled?

[Guest 2]

Yep there are adaption channels within the central convenience module although my hazards flash as standard when locked?

I'll screenshot my coding in the morning but here is a video of the bleep

http://s816.photobucket.com/user/57_audi/media/iPhone%20Uploads/1b8aafad.mp4.html

[Guest 2]

http://i816.photobucket.com/albums/zz90/57_audi/A6/centrallocking_zpscede5d4c.jpg

The 'blink' are the hazards.

Not sure what the Terminal 87 thing is tho.

[techfreak]

Many thanks as always Chris!

I managed to get the beep on lock on working but rather just have hazard flash and no beep as with two babies it's too risky waking em up

[Guest 2]

Just go into Central Convenience, hit Adaption and look in the drop down menu for the Central Locking Functions and change the new value to suit what you want.

[techfreak]

Just go into Central Convenience, hit Adaption and look in the drop down menu for the Central Locking Functions and change the new value to suit what you want.

I checked it when I did the beep but I'm sure it didn't say how to do that...I'll double check

[techfreak]

Found it in the end...it was in there after all. Channel 62 as per your image.

All done now.

Thanks Chris. :-)

[cm.popa]

This is my first post so I shall start by saying hello to everyone !

I own an 55 plate S-line A6 3.0 TDI and I'd like to kindly ask a few questions:

The first one is a little silly regarding the hidden menu activation, I'd like to know what's concept of "drop down menu" in the coding section and also what exactly do you gain access to after enabling it because I can already access the battery meter in the MMI

The next one would be about the Xenon headlights, mine are aiming to low in my opinion and I had a look at an other user xenon coding, an 09 facelift, and it was ending in 03 mine is ending in 16 (I should also mention that I've installed the RS6 headlights with LED DRL that's why I've taken reference from a facelift model, maybe that's wrong) and also when the headlights are off and DRL on I've noticed that on the passenger side the LED's are not dimming when indicating, driver side is. I was wondering if this has something to do with coding as well or something is wrong with the headlight itself.

I shall be looking forward to your wise suggestions !

cheers, Cristian

[Guest 2]

Welcome to VWAF.

As you already have the battery meter there is no real benefit of the hidden menu as you could end up bricking something. If you follow the first post you'll see how to enable it, it's pretty easy.

Does your central convenience module support LED DRL? Some early cars like yours probably doesn't hence why they aren't dimming. You can upgrade your convenience module but we need to see your current version which you can gain from doing an autoscan and pasting it in here.

I assume its been wires up correctly as I remember seeing the DRL needs a direct feed into the central convenience module - I think this was on a A3.

[cm.popa]

Thanks for your quick reply Chris !

I won't go any further the with the hidden menu but I still don't understand how to "drop down the menu" I've tried scrolling down the channels but I don't think that's what it's referring to.

Here is a recent scan that I've done and I was about to ask about the fault codes that I found:

Chassis Type: 4F0
Scan: 01 02 03 05 07 08 09 0E 15 16 17 19 37 42 46 47 4F 52 53 55
56 61 62 72 76 77


VIN: WAUZZZ4F16N057140 Mileage: 139500km/86681miles


00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: Malfunction 0010
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
05-Acc/Start Auth. -- Status: OK 0000
07-Control Head -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: OK 0000
0E-Media Player 1 -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: Malfunction 0010
19-CAN Gateway -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
37-Navigation -- Status: Malfunction 0010
42-Door Elect, Driver -- Status: OK 0000
46-Central Conv. -- Status: OK 0000
47-Sound System -- Status: OK 0000
4F-Centr. Electr. II -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
53-Parking Brake -- Status: OK 0000
55-Xenon Range -- Status: OK 0000
56-Radio -- Status: Malfunction 0010
61-Battery Regul. -- Status: OK 0000
62-Door,Rear Left -- Status: Malfunction 0010
72-Door, Rear Right -- Status: OK 0000
76-Park Assist -- Status: OK 0000
77-Telephone -- Status: OK 0000

-------------------------------------------------------------------------------
Address 01: Engine Labels: Redir Fail!
Part No SW: 4F0 910 402 F HW: 4F0 907 401 B
Component: 3.0L V6TDI G000AG 0030
Revision: --H01--- Serial number:
Coding: 0011372
Shop #: WSC 66565 257 00032


3 Faults Found:
005659 - Glowplug for Cylinder 2 (Q11): Open Circuit
P161B - 001 - Upper Limit Exceeded
Freeze Frame:
Fault Status: 01110001
Fault Priority: 0
Fault Frequency: 1
Mileage: 139366 km
Time Indication: 0
Date: 2013.08.11
Time: 15:57:17


Freeze Frame:
RPM: 0 /min
Torque: 0.0 Nm
Speed: 0.0 km/h
Duty Cycle: 1.0 %
Voltage: 11.86 V
Duty Cycle: 15.0 %
Temperature: 24.3°C


005660 - Glowplug for Cylinder 3 (Q12): Open Circuit
P161C - 001 - Upper Limit Exceeded
Freeze Frame:
Fault Status: 01110001
Fault Priority: 0
Fault Frequency: 1
Mileage: 139366 km
Time Indication: 0
Date: 2013.08.11
Time: 15:57:17


Freeze Frame:
RPM: 0 /min
Torque: 0.0 Nm
Speed: 0.0 km/h
Duty Cycle: 1.0 %
Voltage: 11.86 V
Duty Cycle: 15.0 %
Temperature: 24.3°C


001538 - Internal Control Module: Programming Error
P0602 - 001 - Upper Limit Exceeded
Freeze Frame:
Fault Status: 01100001
Fault Priority: 0
Fault Frequency: 1
Mileage: 0 km
Time Indication: 0


Freeze Frame:
RPM: 0 /min
Torque: 0.0 Nm
Speed: 0.0 km/h
Torque: 0.0 Nm
Inj. Quantity: 0.0 mg/str
Torque: 0.0 Nm
Time: 0.00 ms


Readiness: 0 0 0 0 0


-------------------------------------------------------------------------------
Address 02: Auto Trans Labels: 09L-927-760.lbl
Part No SW: 4F1 910 156 B HW: 09L 927 156 A
Component: AG6 09L 3.0lTDI RdW 0040
Revision: --H01--- Serial number: 4061204
Coding: 0000001
Shop #: WSC 02327 785 00200


No fault code found.


-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 4F0-910-517.lbl
Part No SW: 4F0 910 517 L HW: 4F0 614 517 L
Component: ESP 8.0 quattro H04 0090
Revision: 00000000 Serial number: 00000000000000
Coding: 0020876
Shop #: WSC 02327 785 00200


No fault code found.


-------------------------------------------------------------------------------
Address 05: Acc/Start Auth. Labels: 4F0-910-852.lbl
Part No SW: 4F0 910 852 HW: 4F0 905 852 B
Component: FBSAUDIC6 ELV H31 0220
Revision: 31050601 Serial number: 10600600218330
Coding: 0000019
Shop #: WSC 00196 210 68220


Part No: 4F0 910 131 E
Component: FBSAUDIC6 EZS H44 0070


Part No: 4F0 910 220 D
Component: FBSAUDIC6 IDG H39 0040


No fault code found.


-------------------------------------------------------------------------------
Address 07: Control Head Labels: 4F0-910-7xx-07-H.lbl
Part No SW: 4F0 910 730 F HW: 4E0 035 729
Component: Interfacebox H43 2120
Revision: 00000000 Serial number: 350GX057584827
Coding: 0000002
Shop #: WSC 02335 785 00200


Part No: 4F0 910 609 E
Component: Bedienteil MMIC6H03 0050


No fault code found.


-------------------------------------------------------------------------------
Address 08: Auto HVAC Labels: 4F0-910-043.lbl
Part No SW: 4F0 910 043 HW: 4F2 820 043 J
Component: KLIMABETAETIGUNGH12 0160
Revision: 00000027 Serial number: 00000000163934
Coding: 0001046
Shop #: WSC 02327 785 00200


No fault code found.


-------------------------------------------------------------------------------
Address 09: Cent. Elect. Labels: 4F0-910-279.lbl
Part No SW: 4F0 910 279 HW: 4F0 907 279
Component: ILM Fahrer H15 0080
Revision: 00000000 Serial number: 4F0907279
Coding: 0013121
Shop #: WSC 02335 785 00200


Part No: 4F2 910 113
Component: Wischer AudiC6 H04 0150
Coding: 00062736
Shop #: WSC 02335


Part No: 4E0 910 557
Component: REGENLICHTSENSORH10 0050
Coding: 00141886
Shop #: WSC 02335


No fault code found.


-------------------------------------------------------------------------------
Address 0E: Media Player 1 Labels: 4E0-910-111.lbl
Part No SW: 4E0 910 111 F HW: 4E0 035 111 A
Component: CD-Changer H44 0470
Revision: 00000000 Serial number: AUZ5ZBE7207228
Shop #: WSC 00000 000 00000


No fault code found.


-------------------------------------------------------------------------------
Address 15: Airbags Labels: 4F0-910-655.lbl
Part No SW: 4F0 910 655 E HW: 4F0 959 655 B
Component: 4E AIRBAG AUDI8RH29 0260
Revision: 07H29000 Serial number: 0037LD0944CU
Coding: 0013381
Shop #: WSC 02327 785 00200


No fault code found.


-------------------------------------------------------------------------------
Address 16: Steering wheel Labels: 4F0-910-549.lbl
Part No SW: 4F0 910 549 HW: 4F0 953 549 A
Component: Lenksäulenmodul H07 0230
Revision: 00H07000 Serial number: 90026051950473
Coding: 0102141
Shop #: WSC 02323 785 00200


Part No: XXXXXXXXXXX
Component: Lenkradmodul H07 0080


No fault code found.


-------------------------------------------------------------------------------
Address 17: Instruments Labels: 4F0-910-xxx-17.lbl
Part No SW: 4F0 910 930 A HW: 4F0 920 980 M
Component: KOMBIINSTR. M73 H16 0630
Revision: 00000000 Serial number: 4PX544L75
Coding: 2113443
Shop #: WSC 00999 444 64523


2 Faults Found:
00771 - Fuel Level Sensor (G)
010 - Open or Short to Plus - Intermittent
Freeze Frame:
Fault Status: 00101010
Fault Priority: 7
Fault Frequency: 2
Reset counter: 249
Mileage: 139447 km
Time Indication: 0
Date: 2013.08.12
Time: 07:39:52


00438 - Fuel Supply Sensor 2 (G169)
010 - Open or Short to Plus
Freeze Frame:
Fault Status: 01101010
Fault Priority: 7
Fault Frequency: 1
Reset counter: 211
Mileage: 139489 km
Time Indication: 0
Date: 2013.08.13
Time: 19:01:31




-------------------------------------------------------------------------------
Address 19: CAN Gateway Labels: 4F0-910-468.lbl
Part No SW: 4F0 910 468 A HW: 4F0 907 468 D
Component: Gateway H10 0060
Revision: 10 Serial number: 1200805714822C
Coding: ECFE73C41B3104
Shop #: WSC 02325 785 00200


No fault code found.


-------------------------------------------------------------------------------
Address 37: Navigation Labels: 4E0-910-88x-37.lbl
Part No SW: 4E0 910 888 P HW: 4E0 919 887 C
Component: MNS ECE H45 1060
Revision: 00000000 Serial number: 305GW057619359
Shop #: WSC 02327 785 00200


1 Fault Found:
02927 - DVD Read Error
000 - - - Intermittent
Freeze Frame:
Fault Status: 00100000
Fault Priority: 6
Fault Frequency: 13
Reset counter: 218
Mileage: 136850 km
Time Indication: 0
Date: 2013.07.26
Time: 15:42:52


Freeze Frame:
Hex Value: 0x51F5
Hex Value: 0x74F9
Hex Value: 0x02FF
Hex Value: 0x0204




-------------------------------------------------------------------------------
Address 42: Door Elect, Driver Labels: 4F0-910-793-42.lbl
Part No SW: 4F0 910 793 E HW: 4F0 959 793 E
Component: TSG FA H12 0050
Revision: 00000000 Serial number: 2 ‚
Coding: 0002682
Shop #: WSC 02327 785 00200


No fault code found.


-------------------------------------------------------------------------------
Address 46: Central Conv. Labels: 4F0-910-289.lbl
Part No SW: 4F0 910 289 G HW: 4F0 907 289 G
Component: Komfortgeraet H19 0140
Revision: 01400019 Serial number: 01005747990000
Coding: 0139771
Shop #: WSC 02335 785 00200


Part No: 1K0 951 605 C
Component: LIN BACKUP HORN H03 1301


Part No: 4F0 910 177
Component: Innenraumueberw.H01 0020


No fault code found.


-------------------------------------------------------------------------------
Address 47: Sound System Labels: 4F0-910-223-BO.lbl
Part No SW: 4F0 910 223 D HW: 4F0 035 223 D
Component: DSP-High C6 H09 0170
Revision: PROD_01 Serial number: 00000000798110
Coding: 0000013
Shop #: WSC 02327 785 00200


No fault code found.


-------------------------------------------------------------------------------
Address 4F: Centr. Electr. II Labels: 4F0-910-280.lbl
Part No SW: 4F0 910 280 HW: 4F0 907 280 A
Component: ILM Beifahrer H10 0080
Revision: Serial number: 00000000113163
Coding: 0001103
Shop #: WSC 02323 785 00200


No fault code found.


-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. Labels: 4F0-910-793-52.lbl
Part No SW: 4F0 910 793 E HW: 4F0 959 792 E
Component: TSG BF H12 0050
Revision: 00000000 Serial number: ”ˆ‚
Coding: 0002682
Shop #: WSC 02327 785 00200


No fault code found.


-------------------------------------------------------------------------------
Address 53: Parking Brake Labels: 4F0-910-801.lbl
Part No SW: 4F0 910 801 HW: 4F0 907 801
Component: EPB C63C0030 H03 0030
Revision: C63C0030
Coding: 0000321
Shop #: WSC 02334 785 00200


No fault code found.


-------------------------------------------------------------------------------
Address 55: Xenon Range Labels: 4F0-910-357.lbl
Part No SW: 4F0 910 357 C HW: 4F0 907 357 C
Component: AFS 1 H01 0030
Revision: 00000001 Serial number:
Coding: 0000016
Shop #: WSC 02327 785 00200


Part No: 4F0 941 329 B
Component: AFS-Modul links H02 0020


Part No: 4F0 941 329 B
Component: AFS-Modul rechtsH02 0020


No fault code found.


-------------------------------------------------------------------------------
Address 56: Radio Labels: 4E0-910-541.lbl
Part No SW: 4E0 910 541 L HW: 4F0 035 541 B
Component: TUNER EU/US/RDW H42 0560
Revision: 00000000 Serial number: 394GS057575301
Coding: 0000001
Shop #: WSC 02327 785 00200


No fault code found




-------------------------------------------------------------------------------
Address 61: Battery Regul. Labels: 4F0-910-181.lbl
Part No SW: 4F0 910 181 E HW: 4F0 915 181 A
Component: ENERGIEMANAGER H12 0490
Revision: 00000000 Serial number: 00000000083942
Shop #: WSC 00196 210 83196


Part No: 4F0 915 105 D
Component: von VA0 1507180792
Coding: 344630393135313035442056413031353037313830373932
Shop #: WSC 00000 384 00290


No fault code found.


-------------------------------------------------------------------------------
Address 62: Door,Rear Left Labels: 4F0-910-795.lbl
Part No SW: 4F0 910 795 E HW: 4F0 959 795 E
Component: TSG HL H21 0050
Coding: 0002090
Shop #: WSC 02327 785 00200


1 Fault Found:
02115 - Locking Unit for Central Locking
008 - Implausible Signal
Freeze Frame:
Fault Status: 01101000
Fault Priority: 3
Fault Frequency: 1
Reset counter: 207
Mileage: 139366 km
Time Indication: 0
Date: 2013.08.11
Time: 15:57:17




-------------------------------------------------------------------------------
Address 72: Door, Rear Right Labels: 4F0-910-795.lbl
Part No SW: 4F0 910 795 E HW: 4F0 959 794 E
Component: TSG HR H21 0050
Coding: 0002090
Shop #: WSC 02327 785 00200


No fault code found.


-------------------------------------------------------------------------------
Address 76: Park Assist Labels: 4Fx-910-283.lbl
Part No SW: 4F0 910 283 B HW: 4F0 919 283 B
Component: Parkhilfe 4-Kan H09 0020
Revision: 00H09000 Serial number: 11720520101369
Coding: 0001106
Shop #: WSC 131071 1023 2097151


No fault code found.


-------------------------------------------------------------------------------
Address 77: Telephone Labels: 4E0-910-336.lbl
Part No SW: 4E0 910 336 F HW: 4E0 862 335
Component: Handyvorb2 H10 0580
Revision: 00000000 Serial number: 00000007570713
Coding: 0010900
Shop #: WSC 02335 785 00200


No fault code found.


End ---------------------------------------------------------------------

[gupsterg]

Didn't know where to place ... Link:- MMI 2G Hidden menu (http://www.audi-resource.com/mmihiddenmenu.php)

[ciderhead]

http://i816.photobucket.com/albums/zz90/57_audi/A6/centrallocking_zpscede5d4c.jpg

The 'blink' are the hazards.

Not sure what the Terminal 87 thing is tho.

Tried the above I`m getting no beeps and now my hazards don't flash!! What have I done?!!

[Guest 2]

Go into your program directory and change it back to the original value.

Remember some things here are for pre-facelift cars like the above.

[ciderhead]

Go into your program directory and change it back to the original value.

Remember some things here are for pre-facelift cars like the above.

Will do, thanks Chris.

[Guest 2]

In your C drive (or wherever you installed vcds to) there will be a rosstech folder, inside that you will find a debug folder then you'll find 4 txt files showing all changes made along with each individual module changes

[ciderhead]

In your C drive (or wherever you installed vcds to) there will be a rosstech folder, inside that you will find a debug folder then you'll find 4 txt files showing all changes made along with each individual module changes

Thanks Chris, good to know where to look for the changes made to the modules.

[Lukenkarl]

Has anyone, anywhere done a list of hidden menu options i.e what happens / doesn't happen when you alter the settings. Because going through the numerous settings there is a lot of options.

[gupsterg]

Did pop a link to some stuff in Link:- Post 37 (http://www.vwaudiforum.co.uk/forum/showthread.php?92769-A6-C6-VCDS-Changes-Post-amp-Pre-Facelift&p=838705#post838705)

[toofunkyhouse]

I've just bought my copy, should have it by the weekend. I want to activate the mirror dip, rear parking graphic and needle sweep. Also scan for codes as my blower packed in for two days but now works again... Audi quality

Sent from my HTC One using Tapatalk

[Guest 2]

I've just bought my copy, should have it by the weekend. I want to activate the mirror dip, rear parking graphic and needle sweep. Also scan for codes as my blower packed in for two days but now works again... Audi quality

Sent from my HTC One using Tapatalk

See lower half of post #1.

Remember first of all to clear all faults by pressing Applications on vcds main screen then Erase all DTCs. Ignition off then on and complete autoscan.


Sent from my iPhone using Tapatalk (http://tapatalk.com/m?id=1)

[toofunkyhouse]

Cheers, I'm sure I will do something that will cause all the wheels to fall off!

Sent from my HTC One using Tapatalk

[Guest 2]

Everything's logged (see earlier on in this thread) and reversible so should you mess anything up you can easily revert to standard.

But please oh please if you enable the hidden menu for the MMI stay away from anything you don't know what it does as it's not logged and not as easily reversible.


Sent from my iPhone using Tapatalk (http://tapatalk.com/m?id=1)

[toofunkyhouse]

I don't think I'm fussed about the hidden menu. Thank you though.

Sent from my HTC One using Tapatalk

[toofunkyhouse]

Had a good play with vids tonight, very easy to use. One thing, the mirror dip doesn't go down as much as I would like, is there a way to set where it dips to? Thanks for putting this guid up, very good indeed

[Guest 2]

No setting for the amount of dip, if you have the mirror set lower initially before selecting reverse, it'll dip a bit more.

[M1tchy]

I thought you had to put it in reverse and then it will dip to a point, you then set how much you want it to dip while still in reverse. Once you are happy, drive off and it will level itself. Put it in reverse again and it will go to the position you have set.


Sent from my iPhone using Tapatalk (http://tapatalk.com/m?id=1)

[Guest 2]

Only if you have memory seats and mirrors will it work like that.

[M1tchy]

Ah ok. Something new everyday!


Sent from my iPad using Tapatalk HD

[toofunkyhouse]

Had a play tonight, wanted to check the true millage but it says there is an error and it's not supported.... Also, how can I check if my maps still on the car...

Sent from my HTC One using Tapatalk

[Guest 2]

If this not supported then the ecu doesn't support it ;)

And vcds can't detect remaps.

[toofunkyhouse]

Fair one.

Sent from my HTC One using Tapatalk

[ragebe]

Only if you have memory seats and mirrors will it work like that.

How does one discover if one has memory seats/mirrors? Still think my original coding for the mirror is wrong.

Monday,13,January,2014,19:33:54:41500
VCDS Version: Release 12.12.0 (x64)
Address 52: Door Elect, Pass.
Control Module Part Number: 4F0 910 793 B
Component and/or Version: TSG BF H11 0040
Software Coding: 0001658
Work Shop Code: WSC 02327
VCID: 29592086805B3E56E3D-807C

Advanced Identification
Serial number: fQ
Identification: 000-000
Revision: 00000000
Date: 00.00.00
Test stand number: 0000
Manufacturer number: 0000
Flash Status
Programming Attempts: 0
Successful Attempts: 0
Programming Status: 00000000
Required Conditions: 00000000
Flash Tool Code: 00000 000 00000
Flash Date: --.--.--
Misc.
Hardware number: 4F0 959 792 B
VCDS Info:
Labels: 4F0-910-793-52.LBL


And I can't work out how to get Long Codes as an option in VCDS.

[Guest 2]

Just go into the passenger door module and add the coding to your original value.

A pop up box will show telling you what to add on and where. Pot luck whether it works or not.

The prefacelift doesn't use long coding in door modules.

[ragebe]

Just go into the passenger door module and add the coding to your original value.

A pop up box will show telling you what to add on and where. Pot luck whether it works or not.

The prefacelift doesn't use long coding in door modules.

Yeah, done that a couple of times Chris, added 128 to 1658 to give me 1786 but no joy <sigh>

Guess, it's just too early a module.

[Guest 2]

Its not the door module, its the mirror fitted.

pot luck if you don't have memory.

[toofunkyhouse]

Sorry another stupid question.. here goes, can you in VCDS make the DVD drive on my MMI 3G low... i think.... play normal DVD's on the screen.

[Guest 2]

I think only the HDD version plays DVDs as you're using your drive for nav only iirc


Sent from my iPhone using Tapatalk

[toofunkyhouse]

I have been trying some vcds stuff that I found on another forum but its for a5's I think. You can change the DRL brightness in different situations, add a double disarm bleep but on the A6 I can seem to find this. Can you change the DRL functions?Cheers

[Guest 2]

Have a look through the cent elec module and cent conv modules for coding as they vary between car due to different versions of the module being fitted.


Sent from my iPhone using Tapatalk

[toofunkyhouse]

No can't find anything on drl settings. I also can't get a boot up screen on the mmi. Think I have done everything I can :(

Sent from my HTC One using Tapatalk

[Guest 2]

Splash screen from google How to change startup screen in MMI 3G? | Audi Forum (http://audiforum.us/threads/how-to-change-startup-screen-in-mmi-3g.10798/)

Post #12. Don't click anything you're unsure of.

[toofunkyhouse]

Ahhh there are tick boxes in vcds but they didn't do anything

Sent from my HTC One using Tapatalk

[toofunkyhouse]

To be fair I only wanted to see what it would do... Don't think I will mess further. Cheers though

Sent from my HTC One using Tapatalk

[dan2485]

Wanted to add this from inspectorman63 for a cure to erratic auto wipers.


This is a me too post, but it also has the answer. Having driven my 2006 2.0 TFsi for six months, I too was unimpressed that the intermittent wipers were far too keen to go to maximum wiping and were too sensitive. I ended up never using positions 3 and 4, and rarely position 2. The wiki on the RossTech site is no help; it redirects to an A8 setting which cannot be input into an A6. So I asked them.

After one suggestion which didn't work, they suggested setting the RLS (RegenLichtSensor) coding to 00077101. The setting I had was 00141886. The new setting has transformed the sensitivity of the intermittent wiping from very annoying to usable. Settings one to four now have a usable range of sensitivity, and full speed mad wiping is rarely initiated by the sensor. A great result from RossTech and another reason for buying the genuine gear rather than the moody knock-offs.

This works very well.

[MarkTM]

Great to have the confirmation Dan!

Will try it as my (non-OEM) screen is aquapel treated I need my wipers half as much as most others with untreated screens.

Youtube review of aquapel vs Rainex here:

Rain-X vs. Aquapel - YouTube (http://www.youtube.com/watch?v=K-qhq_AigpM)

Thanks Inspector! :D

[Rs4cab]

Lots of nice usefull info shame I can't get needle sweep tho :(

[Guest 2]

Lots of nice usefull info shame I can't get needle sweep tho :(

It's no real loss ;)


Sent from my iPhone using Tapatalk

[M1tchy]

Lots of nice usefull info shame I can't get needle sweep tho :(

Why can't you have needle sweep?


Sent from my iPhone using Tapatalk

[Guest 2]

Pre facelifts don't support it


Sent from my iPhone using Tapatalk

[Rs4cab]

Only having a2006 model it doesn't support the needle sweep but still lots of other things we can do ;) powerfold mirrors next

[Dutch Paddy]

Oh yes, as from this afternoon my A6 became even sweeter...I now have needle sweep (so cool at night), dipping mirror when selecting reverse, graphics on screen with reversing sensors, battery meter, chirp on locking and a lap timer, oil temp gauge and boost indicator screen on my DIS, all thanks to Chris! Thanks guys!

[Guest 2]

You're welcome! :)

Anything else just give me a shout.

Sent from my iPhone using Tapatalk

[szladob]

This is probably very stupid question, but is it possible to set the distance for the rear parking sensors? Mine beeps continuously when there is still lots of space - makes it safe I guess, but would be good to know when I am e.g. 10 cm instead of 30+...

Other silly question, is there any way to have a meter/gauge visual for the DPF % blockage in the DIS?

Many thanks!

[Guest 2]

Why would you want to change the sensor programming? They're there for a reason? Ie to stop you hitting things.

Never seen a guage for DPF %age, probably not doable. Can read in measuring blocks in vcds though.


Sent from my iPhone using Tapatalk

[szladob]

well, parallel parking into tight spots - it is a bit annoying that it beeps already continuously when you still have "loads" of space... it is a big car, could do with more accurate sensing... I would say when it is continuously beeping, it should mean to stop, not to let's go another 20 cm :)

[Guest 2]

If you have rear factory sensors get the visual lines enabled, will give you a better view and a bit more accuracy

[Dutch Paddy]

The visual aid looks great and gives that little extra info I suppose, but mostly it looks great! Oh, needle sweep in the dark...love it lol


Sent from my iPad using Tapatalk

[s114hed]

Has anyone tested this to see if it was with a FL C6?
http://img.tapatalk.com/d/14/03/20/bene5a3u.jpg


Sent from my iPhone using Tapatalk

[Guest 2]

Don't think the C6 has it.

I think Cent Elec is still short coding on the facelift.

[Guest 2]

Just checked, 09 Cent Elec is still short coding on the C6 so not compatible.


Sent from my iPhone using Tapatalk

[s114hed]

Cheers for the confirmation Chris...think you should be a Audi Tech, probably already know a lot then them anyway 😁


Sent from my iPhone using Tapatalk

[Pityyoufools]

Thanks for the facelift update 😁

Sent from my Nexus 7 using Tapatalk

[szladob]

I just started my new adventure with VCDS, and got the needle sweep going :)
However, when I was trying to activate the visual parking aid (i have rear factory sensors), after changing the number to 2 as described, I got the following error message. Any advice would be greatly appreciated. Many thanks!

24124

[Guest 2]

Press YES and also update your VCDS to the latest version.


Sent from my iPhone using Tapatalk

[szladob]

Many thanks for your quick response; was scared to hit yes, but will try... Since you list an A3 under your post, I was wondering if knew by any chance, if I can find a similar list of possible cool stuff activation for an A3 8P (2009)? Many thanks again!

[szladob]

Dear A6_Chris,

Many thanks for your advice, that was all it needed to hit yes for the park assist... was just concerned as those numbers in the warning (12345) sounded strange, but after hitting yes, all the values remained the same, and now have the visual aid :)... Also needle sweep, lat timer/boost gauge... This is probably a stupid question, but is the oil temp any better than the needle?

[Guest 2]

Oil temp and water temp are different things ....

[MarkTM]

^^^And never get the two fluids confused when topping up your oil/coolant :)

[szladob]

I think i can keep those distinguished for topping up purposes.. :)
On the other hand I may need to do a bit more reading on the value of oil temp... my newly "activated" meter only really starts showing values from about 60 C, until then it is just dashed, and it seems to lag behind the water temp....
The little boost "meter" seems a bit strange, as it shows about a 1/4 of the value even for idling, and even at max acceleration is didn't go to max... :confused:
Is this supposed to refer to the turbo boost? I wonder if after remapping it would show more boost?

[Guest 2]

Oil takes longer to heat up than water, depending on the sensor it will not show values at all times is until the oil is warm to get an accurate reading.

At idle the turbo is still active hence the small reading on the boost guage.

Also it will not show max turbo boost on maximum acceleration as there is a point where the turbo looses boost.

Everything is working correctly as it should!! Don't panic.


Sent from my iPhone using Tapatalk

[A6@georgemac]

OK - my mate has VCDS and I'm borrowing it next week. Couple of Questions - I am going to do items 1,2,4

Facelift Cars - '58 plate onwards

7. Visual Parking Aid - if supported - can someone tell me what difference this makes - my parking aid already looks quite good with bars indicating distance left?

8. Enabling Lap Timer/Boost Gauge/Oil Temp - I probably will do this - unsure

9. Enable Rear DRL (Scandinavian Lights) - can someone tell me what difference this makes?

10. Enable Passenger Mirror Dipping - can anyone enlighten me on the benefit of this one?

Thanks for any help.

[Guest 2]

You ready have number 7 enabled, number 10 dips the passenger mirror when you select reverse to aid not hitting the kerb. It doesn't work to its full potential because you don't have memory seats, it's more a novelty rather than an aid.


Sent from my iPhone using Tapatalk

[Kaiser2000]

Hey guys,

So I previously tried enabling the locking chirp on my A6 (per the first page/post) and while the software accepted the change, it didn't do anything.

Any ideas what to check/try? Cheers!

[Guest 2]

Whats your original short code? Might'nt of added it correctly.

[Kaiser2000]

Whats your original short code? Might'nt of added it correctly.

That was quick Chris :)

I'll have to check it later on but will post back.

[Guest 2]

That was quick Chris :)

I'll have to check it later on but will post back.

Another thing, since yours is Irish spec you might not even have the alarm fitted so check on the drivers door card, below the door lock/catch if you have two small square buttons. If they're there then the alarm is fitted and could just be a coding issue or the siren has failed.

[Kaiser2000]

Another thing, since yours is Irish spec you might not even have the alarm fitted so check on the drivers door card, below the door lock/catch if you have two small square buttons. If they're there then the alarm is fitted and could just be a coding issue or the siren has failed.

I think you just solved the mystery Chris.. went down and had a look there and no buttons. Very strange that as the spec is very high for an Irish car anyway as ya know.

[tony_anon]

Go into your program directory and change it back to the original value.

Remember some things here are for pre-facelift cars like the above.

Hi Chris,

So how to I get the chirp lock confirmation on a post-facelift car (mine's a 60 Reg)? It's not listed in the original post.

Cheers,

Tony

[s114hed]

Tony,

It's the same as the pre-facelift


Sent from my iPhone using Tapatalk

[tony_anon]

Tony,

It's the same as the pre-facelift


Sent from my iPhone using Tapatalk

Cheers mate!

[tony_anon]

Do all the VCDS changes in this thread require the full version or can VCDS Lite be used?

Cheers.

[Guest 2]

Full version only as the C6 isn't compatible with Lite.


Sent from my iPhone using Tapatalk

[Lee82]

Facelift cluster in pre car, ticked active needle test,but no needle sweep, because old control module?

[Guest 2]

Someone else had that issue so I presume its to do with other control modules in the car, possibly the CAN gateway..

[klitoni]

Im not so clear on how to enable "beep beep" on lock/unlock on facelift models.Can someone explain?

Thanks

[Guest 2]

Same as prefacelift


Sent from my iPhone using Tapatalk

[Guest 2]

This wasn't enabled on my 2008/57 car with MMI 2G.

Changing radio source by pressing RADIO

[Select]
[07 - Control Head]
[Adaption - 10]
Additional MMI Options
Add 4 to your existing code (Frequency/Source Change via Function Button Active)
[Test]
[Save]

Try it by pressing the RADIO button to switch between FM/MW/LW/DAB

[anditails]

Same as prefacelift


Sent from my iPhone using Tapatalk
Confirmed. Added this to my 2010 A6 at the weekend.

Im not so clear on how to enable "beep beep" on lock/unlock on facelift models.Can someone explain?

Thanks

[joedredd]

Trying to do mmi high start up, but when carrying out test it states test error and no response from controller. Any ideas?


Have done a full scan with no errors showing, even tried different value of 2 but no joy.

[Guest 2]

What are you trying to do?

[joedredd]

What are you trying to do?

Sorry Chris, its option 6 for pre facelift.

Would the software update sort it?

[Guest 2]

What coding are you doing, post your original.

Try the update, maybe your controller just doesn't support it. I'm assuming you're mmi high?

[joedredd]

What coding are you doing, post your original.

doing the S6 start up, so changed 3rd digit to 1. Still a noob with VCDS so thought this may be easy

[Guest 2]

Post your original coding for control head up :)l
Do the update and try again.

[joedredd]

Post your original coding for control head up :)

I would if I could find it

[Guest 2]

What you're changing to 1 is your original coding.

http://www.vwaudiforum.co.uk/forum/showthread.php?147229-Using-Different-Parts-of-VCDS

[joedredd]

ok going back to car.

[Guest 2]

Take an autoscan and you'll have it saved. Remember to clear and rescan.

Using Different Parts of VCDS (http://www.vwaudiforum.co.uk/forum/showthread.php?147229-Using-Different-Parts-of-VCDS)

Videos - Ross-Tech Wiki (http://wiki.ross-tech.com/wiki/index.php/Videos)

[joedredd]

right back in car, coding is 0011002

[Guest 2]

Do the update and try afterwards.

[joedredd]

Do the update and try afterwards.

will do Chris, thanks for trying.

[joedredd]

Pre-facelift Cars - 04 - 08 plate

2. MMI High Hidden Menu
[Select]
[07 - Control Head]
[Adaption - 10]
Drop-down Menu
[Select - Service Menu]
Change 'New Value'to 1
[Test]
[Save]

Drop-down Menu
[Select - MMI System Retstart]
Change 'New Value' to 1
[Test]
[Save]
*MMI will now restart*
[Done, Go Back]

3. Battery Meter
After MMI restart and Hidden Menu enable - press Radio then hold in Setup + Car for a few seconds (it might take a few times to get timing correct)
[Select] DIAG SETTINGS
[Select] Car Menus Maske
[Select] Battery Level
Scroll to Accept Changes
Press RETURN 3 times
Restart MMI using Setup + MMI Control Knob + Upper Left Inner Key - release


I have just done "5570 update" and wish to put back battery meter (as before), but I am having a problem. I am ok with the first part of MMI high, its when I do the MMI restart after I test the value I get a "Test error" message in the box, any ideas what's going wrong?

[ac606]

Not sure if others have experienced similar.... I added the lap timer/oil temp/boost to a 2011 a6 3.0tdi. All I was after was the oil temp, however oil temp shows --- and the boost is pegged out all the time. No fault codes on the car so my guess is the car cannot support this activated feature?

[Guest 2]

Not all facelift clusters are compatible, there are a few posts throughout the vcds forum.


Sent from my iPhone using Tapatalk

[ac606]

Facelift A6, Poking around on 5F (I forget which byte) I noticed that you can change the Screen from Standard, S Line, S and RS. Although mine is an S Line, it is coded as standard. Wondered if anybody else has tweaked this. Is it safe to do on the facelift models?

[M1tchy]

I did it, all I saw was the fact that the screen showed a different model name and I was getting errors in other modules. Was OK when I put it back.

[ac606]

thanks, I'll not change it then !

[Kegsie]

A6 3.0Tdi Quattro 2008 MMI high
looking to change my electric seats without memory to setup with remote control key fob,
Is there a list of things that you can tweek, automatic parking break when moved to park, battery meter,

[Guest 2]

Page 1 of this thread you'll find whats been done so far.

[Kegsie]

I found this, as I don't have my vag lead yet I cant try it but thanks to C99 if you have electric seats without memory this should work if someone could try it and report.
Go to module 36 Seat Mem DrVr [j136] ,07, Coding change byte 2 bit number 0 , to value 1 (checked).
You should now see Key memory on/off in the MMI settings for drivers seat

If someone can try this and report back that it works.

[MarkTM]

Kegsie, you want to make a mod, my understanding of this thread was that it was for little known facts about changes you could make to your ride via VCDS (could be wrong of course)?

So perhaps you'd have more luck in either the VCDS forum (but as you've said you don't have yours yet) or else a completely new thread in this forum.

Good luck!

[dan2485]

3G PDC Module Setup Procedure.

After installing the Controller, Bumper with PDC’s and the wiring the following needs to be done.

1. Using VCDS open the ‘19’ Can Gateway controller and select the installing list.

2. Check the ‘76’ Park Assist check box and save the settings (this will change the controller coding).

3. Open the ‘76’ Park assist controller and change the coding by changing the second 0 to 2. ( the coding is explained here http://www.audi-portal.com/en/diagno...u_11910.html#1 (http://www.audi-portal.com/en/diagnostic/ecu_11910.html#1))

4. Now click the ‘Do it Now’ box.

5. Now open the ‘5F’ Central Electronics controller and select coding.

6. Now select the long coding helper and click on Byte 8.

7. Now Check the Park Assist check box and close the helper box.

8. Now click the ‘Do it Now’ box.

9. Now you need to access the Hidden menu and select Car then CarMenuOperation.

10. Scroll to Parking Help and press select (BIG KNOB on the MMI) and scroll the setting to 5.

11. Now Press select (BIG KNOB on the MMI) and exit the menu press Radio Button.

12. Now you need to reset the MMI (press SETUP, BIG KNOB and top right soft button together).

You Should have the Parking assist in the MMI.

[tomaslund]

Hi guys!

I can't seem to find any info regarding my current issue.

I have a a6 2006 4.2 fsi quattro pre facelift, but with full nav + color dis.

My problem is that I can't change the color DIS middle screen , it only shows current outside temp... I can change between 1 and 2 on the lower part of the screen, and also get radio channel info + nav info in middle screen but I cannot change it manually to e.g digital speedometer or any other info for that matter. What do I need to do to activate this function?

Best regards,
Tomas

[Guest 2]

you only get digital speedo from a certain model year, think its MY2007 or MY2008, moreso the latter.

[tomaslund]

Thank you Chris, any suggestions of what to do, I was trying to do some stuff as the front page said but couldn't get the reserve mirror function to work, and do you know if there is any chance to activate some Bluetooth on the my2006 ? I did this on my last a6 2008 but it was the newer MMI.

Best regards

Skickat från min SM-G900F via Tapatalk

[Guest 2]

Reverse mirror dip only works on some cars, there is a big thread on the forum.

You can't activate it on MMI 2G, you need to buy the hardware.

[tomaslund]

Oh okey.. so no fun with MMI 2G I guess ? :(
Thx for fast reply !

Best regards

Skickat från min SM-G900F via Tapatalk

[Guest 2]

Not sure if anyone else has noticed but some controllers now support long coding whereas before they didn't.

Just realised this today after turning off all my VCDS mods as I will be saying goodbye to my A6 this Tuesday.

One in particular is #09 Cent Elec. Might not be on all controllers but the version fitted to mine seems to have changed.

VCDS 15.7.1

http://i816.photobucket.com/albums/zz90/57_audi/one_zpsfvndj5mn.png

http://i816.photobucket.com/albums/zz90/57_audi/two_zpsbob9fet5.png

http://i816.photobucket.com/albums/zz90/57_audi/three_zpsxbbtoomh.png

http://i816.photobucket.com/albums/zz90/57_audi/four_zpsu7pkjk70.png

http://i816.photobucket.com/albums/zz90/57_audi/five_zps1bpfyvmq.png

[MFGF]

I will be saying goodbye to my A6 this Tuesday.

Sad day! What's next Chris? Another A6?

[Guest 2]

Sad day! What's next Chris? Another A6?

A 65 reg A4 Black Edition! Don't need the space of a bigger car now. Tuesday has now moved to Wednesday :p

[MFGF]

A 65 reg A4 Black Edition! Don't need the space of a bigger car now. Tuesday has now moved to Wednesday :p

Yay! Another Audi!! :) Would love to see pics once you have the car!!!

[Mr JJ]

Hi guys! I have Audi A6 C6 and was wondering if anybody know how to switch off fog light when unlocking/locking car? I have VCDS? I check 09 cent.elec but couldn't find anything.

[Guest 2]

Press CAR, Exterior Lighting then Coming/Leaving Home, switch this off or turn the timer to 0.

[Mr JJ]

thanks mate, but I was thinking to leave LED strips on when unlock/lock! is there a way to do it with VCDS?

[saifxnyc]

Reverse mirror dip only works on some cars, there is a big thread on the forum.

You can't activate it on MMI 2G, you need to buy the hardware.

What kind of hardware is needed to retrofit a reverse dip mirror on a pre facelift 07 C6?


Sent from my iPhone using Tapatalk

[broadcom]

Hi, i would ask about amp coding. I didn’t find anything about my problem.
I want add aux to my mmi 2g basic (no bose system)
I enabled hidden menu, I activated aux in hidden menu, I connected aux cable to amp in trunk and then I tried to change amp coding to allow aux in.
My original coding is: 080001
I trying to change it to 080041 or 080051 (by this step
0000x?x: Microphone
1 = Microphone (Standard)
2 = Microphone (Voice Control)
4 = Microphone (Analog Input (AUX))
5 = Microphone (Voice Control and Analog Input (AUX))
and when i press “do it”, the error screen say “coding rejected, code out of range”
How can i solve this?
Thanks

[Gunnark100]

what pins you used for aux as they are different? And your mmi mainunit and amp partnumber to have proper info!

[broadcom]

I used pins 26, 24 and 29 in 10 pins connector on amp.
Address 47: Sound System (J525) Labels: Redir Fail!
Part No SW: 4F0 910 223 M HW: 4F0 035 223 N
Component: Amp.-ASK-RD H07 0270
Revision: S1400000
Coding: 080001
Shop #: WSC 02399 823 56573
VCID: 28BA34AF5BFC8B52ADAEED-807D

[Gunnark100]

Aux in should be 4 pins not 3, and for ASK amp i guess coding cant be 5, its either 3 or 4, did you got option aux-in under media menu after you enabled function in hidden menu?

[Gunnark100]

And if you checking your first post, example has 7 zeros, your coding is only 3 bytes long, so try changing 4th number from left!

This should be ask amp for c6,but never know:
Long code:
The long code comprises 3 bytes, and is composed as follows:

1. Byte Interior spec:
xx0000
01 Right-hand drive, cloth trim, diesel engine
02 Left-hand drive, leather trim, diesel engine
03 Right-hand drive, leather trim, diesel engine
04 Left-hand drive, cloth trim, petrol engine
05 Right-hand drive, cloth trim, petrol engine
06 Left-hand drive, leather trim, petrol engine
07 Right-hand drive, leather trim, petrol engine
08 Left-hand drive, cloth trim, diesel engine

2. Byte Microphon spec:
00xx00
00 No microphone
01 1 Microphone
02 - Invalid -
03 No microphone and analog input (AUX) activated
04 1 microphone and analog input (AUX) activated

3. Byte Variant:
0000xx
00 Saloon
01 Avant / Allroad

[broadcom]

Yes i shoul be 4 pins bud aux cable have L+ R+ and ground. In my old bmw this worked fine but here should be 4. I can merge ground togerher.
Yes i got. When I press Media button, then top right choose source I see aux in screen with “aux-in is now active” or some like this but no sound.

[broadcom]

And if you checking your first post, example has 7 zeros, your coding is only 3 bytes long, so try changing 4th number from left!

This should be ask amp for c6,but never know:
Long code:
The long code comprises 3 bytes, and is composed as follows:

1. Byte Interior spec:
xx0000
01 Right-hand drive, cloth trim, diesel engine
02 Left-hand drive, leather trim, diesel engine
03 Right-hand drive, leather trim, diesel engine
04 Left-hand drive, cloth trim, petrol engine
05 Right-hand drive, cloth trim, petrol engine
06 Left-hand drive, leather trim, petrol engine
07 Right-hand drive, leather trim, petrol engine
08 Left-hand drive, cloth trim, diesel engine

2. Byte Microphon spec:
00xx00
00 No microphone
01 1 Microphone
02 - Invalid -
03 No microphone and analog input (AUX) activated
04 1 microphone and analog input (AUX) activated

3. Byte Variant:
0000xx
00 Saloon
01 Avant / Allroad

I ´ll try this step in this afternoom and let you know.
Thank you

[broadcom]

I coded amp by your instruction. It work. Thanks.
But still no sound from aux. I pinned every 4 pins and nothing happend.
Exist some pins scheme for ask amp? A found yust 32pin bose amp and it shoul be different.

[Gunnark100]

I coded amp by your instruction. It work. Thanks.
But still no sound from aux. I pinned every 4 pins and nothing happend.
Exist some pins scheme for ask amp? A found yust 32pin bose amp and it shoul be different.

preFL C6 and only aux/in is a nightmare, I will pm you a bit info later, but you might be out of luck here:(

Your amp official pinout should be this:
23 - Microphone for J507 (+)
25 - Analog input (+)
27 - Loop break diagnostic wire
28 - Microphone for J507 (-)
30 - Analog input (-)

[broadcom]

I am very sad. It look very simply “add aux” but it not works and i dont know why.
-i unlocked hidden menu
-i activated aux in hidden menu
-i pinned aux to connector on amp at 25+, 30-
-i coded amp from 080001 to 080301(tried 080401 too)
And..... still no sound... 🙁
Is different between preFL and FL in pin scheme? I have C6 2010. Its FL isnt it?

[Gunnark100]

I am very sad. It look very simply “add aux” but it not works and i dont know why.
-i unlocked hidden menu
-i activated aux in hidden menu
-i pinned aux to connector on amp at 25+, 30-
-i coded amp from 080001 to 080301(tried 080401 too)
And..... still no sound... 
Is different between preFL and FL in pin scheme? I have C6 2010. Its FL isnt it?

:zx11: you said you have mmi 2g basic???? Whats your mmi part number, 5f module with vcds...2010 cant be 2g anymore:)

[broadcom]

I said this. Because i found at web compararion mmi and my menu looks very old like basic. I should be bad picture... i dont have 5F in vcds just 07 Control head. Is it it?

[Gunnark100]

I said this. Because i found at web compare mmi and my menu looks very old like basik. I should be bad picture... i dont have 5F in vcds just 07 Control head. Is it it?

This is strange 2010, anyway give us control head 07 number...

[broadcom]

This is strange 2010, anyway give us control head 07 number...
Vag number: 4F0 910 733 H
Component: Interfacebox H43 5140
Soft. Coding: 0003002
Shop#: imp:000 WSC 00000
Extra: 4F0910609E Bedienteil MMIC6H01 0060
Extra: Garaet 00000

[Gunnark100]

Vag number: 4F0 910 733 H
Component: Interfacebox H43 5140
Soft. Coding: 0003002
Shop#: imp:000 WSC 00000
Extra: 4F0910609E Bedienteil MMIC6H01 0060
Extra: Garaet 00000

Check your pm box, I sent few links etc, maybe you find something useful!

[broadcom]

Ok, im going to check pm box. Thank you for all

[waelaburezeq]

I coded amp by your instruction. It work. Thanks.
But still no sound from aux. I pinned every 4 pins and nothing happend.
Exist some pins scheme for ask amp? A found yust 32pin bose amp and it shoul be different.

Hi mate,

I know this has been around 4 years, but hopefully you can help me! you are my last chance :)

I have Audi A6 C7 2014 (pre-facelift) with RMC low screen (NO AUX, No AMI, No SD Card). The only media source I have is CD and I need to find a way to install AUX (or AMI) on my amp. My amp is "Audi Multimedia" .

I am attaching my screen HW and SW version coming from the hidden green menu (no diag option to enable AUX from there) so I coded the AUX through VCDS, 5F module, Byte 8 , enabled bit 4 as in this guide (https://integratedautomotive.co.uk/activating-aux-input-on-audi-mmi-3g-and-mmi-mib1/)but I still don't see it on my media screen as a source (and I do still see CD only)


All I need again, is just AUX source!


38772