coil light flast and engine manangment sensors around the Exhaust help with output

[bashman40]

Hello ladies and gents.

i own a 2009 vw golf tdi 1.6 im getting the above issues so i plugged it in to find the blow fault code so i replaced the Exhaust Gas Temp EGT Sensor (https://www.ebay.co.uk/itm/Exhaust-Gas-Temp-EGT-Sensor-Some-VW-Golf-Mk5-Mk6-1-6TDI-2-0TDI/312474539717?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649)(black plug)

1 Fault Found:
14355 - ROD - Unknown Error Code
- 00 [167]
MIL ON - Not Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Mileage: 118354 km
Date: 2019.10.24
Time: 18:35:58


Readiness: 1110 1000

after replacing the sensor i now have these code below ? help!
2 Faults Found:

14356 - Exhaust Gas Temperature Sensor 4 Bank 1
P246E 00 [032] - Electrical Malfunction
Intermittent - Not Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Date: 2000.00.00
Time: 00:00:00

Engine speed: 0.00 /min
Normed load value: 0.0 %
Vehicle speed: 255 km/h
Coolant temperature: 78 °C
Intake air temperature: 14 °C
Ambient air pressure: 980 mbar
Voltage terminal 30: 12.536 V
Unlearning counter according OBD: 40

10107 - Sensor 1 for Exhaust Temp Bank 1 (G235)
P0544 00 [175] - Circuit Malfunction
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Mileage: 118365 km
Date: 2114.14.02
Time: 22:06:52

Engine speed: 1652.75 /min
Normed load value: 0.0 %
Vehicle speed: 65 km/h
Coolant temperature: 76 °C
Intake air temperature: 16 °C
Ambient air pressure: 980 mbar
Voltage terminal 30: 14.118 V
Unlearning counter according OBD: 40
Exh.gas temp.sen 1-TEG_MES[0]: 19.98 °C
Exh.gas temp.sen 3-TEG_MES[1]: 192.04 °C
Exh.gas temp.sen 4-TEG_MES[2]: 188.10 °C
Outside air temperature-Ambient temperature: 6.00 °C
Time since engine start: 165 s
Coolant temperature: 82 °C
Coolant temperature at radiator outlet: actual value-TCO_2: 29 °C

[bashman40]

also a diagram with the banks and sensor numbers woul de useful if anyone can direct me to

[bashman40]

any help on this issue ladies and gents ??

[bashman40]

which sensor is Sensor 4 Bank 1 and Sensor 1 for Exhaust Temp Bank 1 can someone point them out for me ?

[Crasher]

What are you using as a diagnostic system?

[bashman40]

What are you using as a diagnostic system?

thnaks for the response, VCDS version 19 is what im using.

[Crasher]

I think your interface is causing the problem with the code, which one do you have?

[bashman40]

I think your interface is causing the problem with the code, which one do you have?

Can you elaborate on “interface”

[Crasher]

Your VCDS interface, what is it? Before I upgraded to the HEX NET I was having similar unknown code issues.

[bashman40]

Your VCDS interface, what is it? Before I upgraded to the HEX NET I was having similar unknown code issues.

Meaning my Diagnostic system Is ross tech can you guide me plz this one-has really annoyed me to resolve

[Crasher]

Which VCDS interface do you have, the one you plug into the diagnostic socket? The curent top version is HEX-NET.

VCDS | Product categories | Ross-Tech (https://store.ross-tech.com/shop/cat/VCDS)

[bashman40]

Which VCDS interface do you have, the one you plug into the diagnostic socket? The curent top version is HEX-NET.

VCDS | Product categories | Ross-Tech (https://store.ross-tech.com/shop/cat/VCDS)


Yh hex-net

[bashman40]

Anyone got a diagram from for sensor is in what bank with bank number numbered

[Crasher]

You need to raise this with Ross Tech as to why it is an unknown code.