PDA

View Full Version : DMF being changed, anything else?


sam2k01
02-02-2015, 03:39 PM
Hi i'm getting my dual mass flywheel changed today, and just wondering because it's a big job is there anything else i should be doing while its being done?
Guest 2
02-02-2015, 03:39 PM
Hi i'm getting my dual mass flywheel changed today, and just wondering because it's a big job is there anything else i should be doing while its being done?

Clutch.
sam2k01
02-02-2015, 04:20 PM
Thanks for the reply, but sorry, should of mentioned it's a 2.0tdi multi tronic cvt. One of garages said I need to change the spigot bearing at the same time? Is this true for the multitronic?
EssexGonzo
02-02-2015, 06:05 PM
I'd go for the starter motor too. Whilst the DMF is out the motor will be simple. Apparently. :rolleyes:

I got mine changed when the DMF was changed as the indy specialist reckoned it was one of the causes of the DMF failure. And he reckons that starter motors go over time anyway. Certainly the experience I've had on 2 or 3 diesels now.
sam2k01
02-02-2015, 07:01 PM
Top advice mate! Will check up on the prices and hopefully get it done! 👍
sam2k01
19-02-2015, 01:10 AM
Quick update, DMF was changed, fixed the problem with the rattling on a hot start. Horrible noise, got a little bit embarrassing by the end when there was passengers in the car :S. All is well now!
EssexGonzo
19-02-2015, 10:55 AM
Those were my symptoms too, great you've got it sorted.

Did you get starter motor done too? If not, problem might come back over time.
sam2k01
19-02-2015, 11:04 AM
Starter motor wasn't delivered on time and the garage was being a bit of a douche about it, so just cancelled the order and left it. Hopefully, it stays strong!
MarkTM
19-02-2015, 02:42 PM
If anything like my 3.0 then the starter can be changed from underneath quite easily in your own time.
audimeister
15-10-2015, 02:45 PM
Hello mate,

How much did it end up costing you then? Parts + Labour? Is there anywhere you would recommend to purchase the Flywheel from?
sam2k01
15-10-2015, 05:00 PM
Hi mate, highly recommend LUK flywheel, don't be tempted by the cheaper stuff, just not worth the hassle and I got mine from carparts4less, but check out eBay too. The flywheel was 200 with discount codes and fitting was another 150 at my local indie.
audimeister
16-10-2015, 11:05 AM
Hi mate, highly recommend LUK flywheel, don't be tempted by the cheaper stuff, just not worth the hassle and I got mine from carparts4less, but check out eBay too. The flywheel was 200 with discount codes and fitting was another 150 at my local indie.

Thanks bud :)
Northernstar002
23-10-2015, 01:35 PM
How long would you exepct the flywheel to last for (mileage wise) and what are the symptoms of a failing one?
sam2k01
23-10-2015, 04:01 PM
How long would you exepct the flywheel to last for (mileage wise) and what are the symptoms of a failing one?
My last one lasted 50k, but I think they supposed to go for about 60k. Symptoms are rattling noises coming from the front when starting the car when it's hot.

I'm sure others will give you more symptoms but that was the one bothering me the most.

Sent from my Vodafone Smart ultra 6 using Tapatalk
Northernstar002
27-10-2015, 02:42 PM
Hmmm, I get a ratling from the car when it's on tickover. I suspect a ratling heat shield above the exhaust. I think my clutch is past it's best as the biting point is quite high and sometimes I get quite alot of judder when setting off in first when cold.

Anything else that might indicate a failing DMF?