philfingers
06-02-2011, 04:10 PM
I've fitted DIS and Cruise to my 2003 Avant. I also changed the Steering Controller for a used Q model, which supports the DIS and Cruise. I've got the Cruise working but the ABS and ECU lights are on constantly, so I can't even see if the DIS is working or not. The rear wiper is working now.
I've got the following coming up on scanning:-
Chassis Type: 8E - Audi A4 B6
Scan: 01,02,03,08,09,15,16,17,26,36,37,45,46,55,56,63,76
-------------------------------------------------------------------------------
Address 01: Engine
Controller: 038 906 019 JT
Component: 1,9l R4 EDC G000SG 1572
Coding: 00003
Shop #: WSC 63351
WAUZZZ8E13A347611 AUZ6Z0C0016661
2 Faults Found:
18097 - Powertrain Data Bus: Implausible Message from Elect. Load Controller
P1689 - 35-00 - -
17964 - Charge Pressure Control: Negative Deviation
P1556 - 35-10 - - - Intermittent
Readiness: N/A
-------------------------------------------------------------------------------
Address 03: ABS Brakes
Controller: 8E0 614 517 A
Component: ABS/ESP allrad 1729
Coding: 00000
Shop #: WSC 00000
2 Faults Found:
00778 - Steering Angle Sensor (G85)
66-10 - Not Matched - Intermittent
01044 - Control Module Incorrectly Coded
35-00 - -
-------------------------------------------------------------------------------
Address 16: Steering wheel
Controller: 8E0 953 549 Q
Component: Lenksáulenmodul 0801
Coding: 00042
Shop #: WSC 00672
No fault code found.
What I'm struggling with is the Login in for the ABS Brakes. I think the correct coding I need is 09355. But I can't seem to get in. Once I'm in I think I need the coding set to 04255 which is:
9- A4
3- FN3 16" (PR-1LT/1LF) - brakes
5- 4/6cyl Diesel
5- Manual
SCSM coding I've used is 00042
4- DIS and Cruise
2- Rear wiper (avant)
Also the car is well down on power, the fault code is
17964 - Charge Pressure Control: Negative Deviation
Whilst I was working on the car yesterday I pulled the top engine/cam cover off to inspect the cam and the loom, as I have a intemittent misfire. I think I may have disturbed one of the 3 pipes which run to the LHS of the cover, need to check for holes in those.
Any help appreciated.
I've got the following coming up on scanning:-
Chassis Type: 8E - Audi A4 B6
Scan: 01,02,03,08,09,15,16,17,26,36,37,45,46,55,56,63,76
-------------------------------------------------------------------------------
Address 01: Engine
Controller: 038 906 019 JT
Component: 1,9l R4 EDC G000SG 1572
Coding: 00003
Shop #: WSC 63351
WAUZZZ8E13A347611 AUZ6Z0C0016661
2 Faults Found:
18097 - Powertrain Data Bus: Implausible Message from Elect. Load Controller
P1689 - 35-00 - -
17964 - Charge Pressure Control: Negative Deviation
P1556 - 35-10 - - - Intermittent
Readiness: N/A
-------------------------------------------------------------------------------
Address 03: ABS Brakes
Controller: 8E0 614 517 A
Component: ABS/ESP allrad 1729
Coding: 00000
Shop #: WSC 00000
2 Faults Found:
00778 - Steering Angle Sensor (G85)
66-10 - Not Matched - Intermittent
01044 - Control Module Incorrectly Coded
35-00 - -
-------------------------------------------------------------------------------
Address 16: Steering wheel
Controller: 8E0 953 549 Q
Component: Lenksáulenmodul 0801
Coding: 00042
Shop #: WSC 00672
No fault code found.
What I'm struggling with is the Login in for the ABS Brakes. I think the correct coding I need is 09355. But I can't seem to get in. Once I'm in I think I need the coding set to 04255 which is:
9- A4
3- FN3 16" (PR-1LT/1LF) - brakes
5- 4/6cyl Diesel
5- Manual
SCSM coding I've used is 00042
4- DIS and Cruise
2- Rear wiper (avant)
Also the car is well down on power, the fault code is
17964 - Charge Pressure Control: Negative Deviation
Whilst I was working on the car yesterday I pulled the top engine/cam cover off to inspect the cam and the loom, as I have a intemittent misfire. I think I may have disturbed one of the 3 pipes which run to the LHS of the cover, need to check for holes in those.
Any help appreciated.