Notices
 
 

  

User Tag List

Thread: ##B6 Front Headlight & Tail light REPLACEMENT Guide! ## UPDATED> GUIDE NOW UPLOADED

Page 15 of 15 FirstFirst ... 5131415
Results 141 to 143 of 143
  1. Re: ##B6 Front Headlight & Tail light Guide! ## UPDATED> GUIDE NOW UPLOADED 
    Join Date
    Aug 2008
    Location
    Newcastle upon tyne
    Posts
    10
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)
    Hi Allen

    Just turn it up over and the light fitting becomes loose giving you loads more space to change the blub.
     
    1 0 0
     

  2. Re: ##B6 Front Headlight & Tail light REPLACEMENT Guide! ## UPDATED> GUIDE NOW UPLOADED 
    Join Date
    Aug 2017
    Posts
    1
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)
    First, a sincere thank you to RickT for the excellent how-to.

    First time having to change a rear bulb since acquiring an A4 Avant earlier in the year. Handbook: "A specialist job requiring some dismantling, take it to your Dealer." Yeah, right!

    I've no doubt I would have figured it out after some amount of exploration, however I have a high regard for one-Marque forums and was delighted to find VWAF for VAG advice and expertise.

    In case it helps someone coming along later with the same job ahead, the only real point to watch for is that the small bolt securing the cluster unit - the only thing you have to undo other than the cable-connector once the unit is free - doesn't drop behind the outer panel before you fully withdraw it, else it would be a total pain to recover unless you got lucky dabbing around with a magnetic retriever maybe.

    It is worth noting that if there are two of you you don't have to remove the bolt completely to free the cluster unit, just back it off past its 'bite' point but be careful to approach it carefully as there's barely a couple more turns then left on the thread before it would be free to drop in to the abyss below it!

    So the person on screwdriver-duty needs to be cautious when that point is getting near, it is a bit of a by-feel process with input from the other person checking if the cluster is showing signs of being loose/free.

    And it would help if you know beforehand whether the bolt is short or long so so you don't start going slowly in quarter-turn-and-try-once-more increments after 1/4" when the bolt is 1.5" long! Hopefully one of the photos I have added will help a little on that anyway.

    But if there's just one of you to get the job done, it is more than sensible to take steps to capture the bolt once loosened part-way, even if your driver-tip is magnetic - it is a long-ish bolt in a tight-ish location and could accidentally get jostled-off as you withdraw it if you make unlucky contact with the body/panel/trim edge or are withdrawing off-straight without being aware of it. It happened to me many years ago now and gave me a truly torturous time recovering a special-fitting small bolt-on component on a lovely old Merc, that due to age and specialism I could only have replaced by getting one made .. which would also have needed the one I had dropped as a pattern!

    The bolt you are withdrawing has a small hex-head and also takes a phillips/crosshead driver. It is located within the centre of what has the appearance of being a larger hex-headed bolt because of the limited view and the shading caused by the inset and the small access hole through trim/panel. At first glance this can give the impression that you need to undo *the large bolt* that you think you are seeing, which sets you off scratching your head because it is larger than the hole you would have to withdraw it through as well as being unable to get a socket on it through that hole in the first place!

    But really it is dead simple, all you have to do is realise/observe that the deal just needs a suitable driver in the crosshead and you are golden. I think it is probably possible for a smaller socket to be able to locate over it on a 1/4" bar if you have a small-set, but I didn't bother trying as it was nothing more than a handy-screwdriver job and I already had one right there.

    If you can get a small socket through and over it without interference from the collar surrounding it, then presumably that would also hold the head steady on withdrawal ... however, the head is only shallow and the bolt is relatively lengthy and so there could still be a possibility of it dropping out or being dislodged by accident so be aware.

    If using a screwdriver however then there's many little tricks such as using blu-tac on the driver-tip (sometimes fails to work, so okay unless you need a guaranteed result), or sliding a tube over the screw/nut head if there's enough access and unscrewing through that tunnel-to-safety.

    A simple method that I have used countless times over the years and have never gone wrong with however, is to use the barrel of a felt-tip pen or similar. Not the rigid-plastic type as they can shatter or at least split in the process, but the softer-plastic type, firm but with a little give.

    The idea is to back-out the bolt/screw a short way with a screwdriver so it turns easily and also has the head exposed, and then ease the end of the pen-barrel over it making sure to keep the same axis as the screw/bolt for max stability. And you don't even have to lose a perfectly good pen in the process - most of them have an end-cap and you just remove that and there's some clear space before you see the ink-tube or whatever ... use it and pop the end cap back after and it's a pen again! In my case however my toolbox had just acquired a first Audi-special tool

    (At a push, use a rigid one, let it split, take it off and then wrap sticky/gaffer/parcel tape around it a few turns to restrict the split and give the springiness you need, then push it gently back on making sure that the screw/bolt is free to turn ... just be a little more careful!)

    For this job an old CD marker pen was pretty perfect, very slightly small but that only meant I needed to be a little more slow and gentle locating it right down over the head of the bolt - usefully snug as the head is not that deep. Once there it was held perfectly securely and I was able to finish undoing it and withdrew it very easily. The whole job from removing the bolt to replacing it again with the cluster back and a new bulb fitted was less than 5 minutes.

    I hope this is useful to someone, and that the photos help - I presume they are thumbnails and will enlarge when clicked.

    A4 1.JPG

    A4 2.JPG

    A4 3.JPG

    A4 4.JPG

    A4 5.JPG

    A4 6.JPG
     
    0 0 0
     

  3. Re: ##B6 Front Headlight & Tail light Guide! ## UPDATED> GUIDE NOW UPLOADED 
    Join Date
    Apr 2019
    Posts
    1
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)
    HI Rickt - Thanks for the guide - it's not quite the same on my Audi A4 cabriolet from 2005 - but close enough to make your guide very worth while! Thanks
     
    0 0 0
     

Page 15 of 15 FirstFirst ... 5131415

Similar Threads

  1. Replacement Stop & Tail Light Bulb
    By Black Cab in forum Audi A4 - B6 Forum - 2002 - 2005
    Replies: 14
    Last Post: 18-05-2011, 10:40 AM
  2. W8 light fitting guide - Sorry but can't find
    By fasteddie84 in forum Golf MK4 - 1999 - 2004
    Replies: 2
    Last Post: 15-04-2008, 11:21 AM
  3. A4 rear disc replacement - renew guide pins?
    By anthonyj in forum Audi A4 - B6 Forum - 2002 - 2005
    Replies: 0
    Last Post: 19-02-2008, 10:31 PM
  4. Lamp Replacement Guide
    By shahabudeen in forum Audi A4 - B6 Forum - 2002 - 2005
    Replies: 10
    Last Post: 15-04-2007, 10:12 AM
  5. What about a where to get guide
    By paddyboy in forum Passat - Archive Topics
    Replies: 1
    Last Post: 06-01-2007, 06:43 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


 



  


Disclaimer: VW Audi Forum is an "independant enthusiast website", administered in line with guidelines supplied by VAG in the UK, and is in no way related to any of the Worldwide Volkswagen,Audi,Seat,Skoda,Bentley,Bugatti,Porsche or Lamborghini group of Companies. For official up to date information on any of there vehicles, please visit the official websites. Any comments made throughout this website, are the views of the respective poster, and in no way represent the views of the VW Audi Forum Administration, or the worldwide Volkswagen & Audi Group of companies.


VW Audi Forum do not vet and are not responsible for any information which is posted in this forum. All content is viewed and used by you at your own risk and we do not warrant the accuracy or reliability of any of the information.


Copyright: Certain "words", "phrases" and "Images" used on this website by the Administration are "Copyright" of Volkswagen GB, Volkswagen AG (Germany), Audi GB, Audi AG (Germany), Volkswagen Motorsport GB, Volkswagen Motorsport AG (Germany), Audi Motorsport AG (Germany), Volkswagen Racing GB, Bentley, Bugatti, Porsche and Lamborghini. No image can be replicated by anyone WITHOUT the relevant Companies written permission.


All trademarks and copyrights remain property of their respective owners.

No part of the VW Audi Forum website or forum may be reproduced without written permission from the site administration


PLEASE NOTE - PERSONAL ABUSE, ABUSE AGAINST THIS OR ANY OTHER WEBSITE OR ANY COMPANY WILL NOT BE TOLERATED. OFFENDERS WILL BE MODERATED OR EVEN BANNED.


This website and forum are best viewed at a minimum resolution of 1024 by 768.



  



- VW AUDI Forum - The #1 Volkswagen (VW) Group Forum - Volkswagen (VW) - Audi - Seat - Skoda - Bentley - Bugatti - Lamborghini - Porsche - Scania - MAN - Ducatti - VW Audi Forum -


- www.vwaudiforum.co.uk - www.vwaudiforum.co.uk -