Notices
 
 

  

User Tag List

Thread: Replacing Intake Manifold - Done! Some Tips...

Results 1 to 3 of 3
  1. Replacing Intake Manifold - Done! Some Tips... 
    #1
    Join Date
    Oct 2015
    Location
    Newcastle upon Tyne
    Posts
    15
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)
    Prologue: I was getting idle twitching and intermittend P2015 errors, but no lights on the dash. My car is not a Golf, nor is it even a VW. I have a 2010 Octavia VRS, but the engine is the CCZA 2.0TSI which is almost identical to the Golf R (?) I believe.

    Job's complete, eventually... Taking the IM off, fitting all the bits to the new IM, cleaning the valves, ports, and TB, and then fitting it all back together.... took me about 20 hours in total, maybe more! It is a right horrible job to do, but it was very necessary.

    Annoyingly, it hasn't cured my warm idle engine twitching, but the throttle response and acceleration have improved from what I can tell. Never had it on a rolling road so have no stats to compare, but it definitely seems better so far. I was getting intermittent p2015 errors indicating a fault with the IM. It never brought up a dash light, but I knew that the carbon buildup would be an issue with the car having 70k, so I coughed up £130 and bought a new IM from the US and replaced it whilst I had it off to clean the carbon.

    Apologies as I'd set off to document the process and do a write up, but it quickly became a bit of a nightmare and took twice as long as I expected. Having said that, I'm glad I did it and am proud that the novice that I am managed to do it without breaking anything or making any serious mistakes.


    Things to note:

    • The bracket under the IM is a git to remove and get back on. I could only do it by taking the throttle body off the IM. To do that you'll need to remove the intake breather pipe from the front that runs down to the radiator. Two T30 captive bolts hold it on. You'll need a 10mm Triple Square, which I didn't realise I didn't have until I'd taken half of the engine bay apart. I cheated and used a t50 torx which damaged the head of the bolt, so I'd only say do this if you literally have no choice like in my case.
    • ..
    • That breather pipe is a git to remove and get back on. It took a good hour of messing around and fiddling. There is no room for wiggling, but there seems to be a magic angle, which out of the blue, I seemed to get and it slotted straight in. Make sure you connect the sensor before tightening up the two t30 bolts as the clearance for the sensor connector is minimal.
    • ..
    • The TB is also a git to remove and get back on. Only 4 self tapping t30, but getting a tool in from above or from under the car is a nightmare - there just simple is no room to get a ratchet in and the angles are horrific. It would have been a lot easier I think if my extensions bars were rigid and not wobble bars, but alas I didn't have any...
    • ..
    • Spotting the pattern here? Most things in this job were gits to remove and reinstall....
    • ..
    • Picks! You'll want little picks of different styles. You will not get all of the carbon desposits from the valves/ports without them, no matter how hard you try. I started by scratching the dry carbon gunk off with a flat screwdriver, and blasting the bits out with an air duster, making sure to catch it in a towel. Make sure the valves you're working on are closed, and that all others are block with rags. Also, make sure the injector holes (if they come out with the IM - all 4 did for me!) are blocked - you really don't want this crud dropping into the chambers!
    • ..
    • Seafoam... Totally overrated IMO. I found Wynn's Carb and Injector Cleaner to work much better. Once the main chunks of carbon were picked off with a flatblade and picks, I flooded the ports with carb cleaner and let it sit for 10 mins or so. With the carb cleaner still in, I attacked it again with picks and a brass bottle brush by hand before extracting the fluid/gunk with a hand pump. I put more carb cleaner in then attacked it with fresh brass brush in a drill. Sounds very harsh, but it'd be very difficult to do damage in here - just don't do anything stupid or jam things in hard and you'll be fine. Once the thick stuff is off, it cleans up surprisingly well (see photos).
    • ..
    • Take photos! There are a lot of connectors. The loom is done in a way that connectors can only really go back where they came from, but you'll be disconnecting a good 15 sensors/connectors to get in and remove the parts, so make sure they all go back!
    • ..
    • Be prepared for stripped bolts. Two T30 bolt holes in the head for the IM lost their threads when I took the bolts out. Previous owners/mechanics obviously had the IM out at some point and overtightened them putting them back in. I was very careful putting them in (worked with RC helicopters for a decade so used to not over tightening bolts) making sure not to cross-thread them. I had no choice just to put them back in so right now, my IM has two bolts that are nowhere near as tight/secure as they should be.
    • ..
    • You'll need new fuel injector seal kits at about £8.50 each. Buy four, maybe even 5 so you have spare. The teflon seals are not hard to fit, but you need a specialist VW tool to do so and you only get one attempt. If you warp or damage that seal, scrap it and try again, otherwise you'll get a lovely 1500psi fuel leak. On the subject, make sure you clean the injector nozzles whilst they're out. I used seafoam and a clean, lint free rag as well as soft brush.
    • ..
    • When you refit the IM, make sure the injectors are all plugged in, and that you push down on the wiring harness so the IM can slide back into place. If you forget, it’ll all have to come off again as you’ll not get your hands in afterwards!




    Dirty, gunky valves:






    Clean valves:






    Dirty injector nozzle:



    Clean TB:


    Full album: Intake Manifold Replacement - Google Photos

    These videos are very helpful:
    Intake Manifold for VW and Audi 2.0T TSI DIY (How to) Replacement - YouTube
    2008 VW Audi 2.0T TSI intake manifold carbon build up cleaning by Edge Motors - YouTube

    VW T10133C Tool:
    This is not cheap at about £150, but I got it used off ebay for about half that. There are clones out there for about £35 but given the tight, precise tolerances, I personally wouldn't use anything other than the official tool. If you need to use it, give me a shout and I'd be happy to lend it out.


    I'm sure I'll think of more to add, but if you have any questions, give me a shout and I'll do my best to help.

    Thanks for reading!

    EDIT: Sorry for the wall of text. I had the bullets spaced for easier reading, but it keeps stripping out the line breaks when I save the post. Not sure there's anything I can do about that, short of putting it into a table.
    EDIT2: Added dots A cheat, but helps for reading.
     
    0 1 0
     

  2. Re: Replacing Intake Manifold - Done! Some Tips... 
    #2
    Join Date
    Oct 2015
    Location
    Newcastle upon Tyne
    Posts
    15
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)
    Wow, not even one reply or thanks button...
     
    0 0 0
     

  3. Re: Replacing Intake Manifold - Done! Some Tips... 
    #3
    Join Date
    Oct 2017
    Location
    Halifax, West Yorkshire
    Posts
    151
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    22 Post(s)
    Amazing work, how you turned those dirty valves brand new is great.
     
    0 0 0
     

Similar Threads

  1. Question Intake manifold need replacing??
    By Bethj in forum Audi A4 - B7 Forum - 2005 - 2008
    Replies: 5
    Last Post: 21-04-2014, 03:04 PM
  2. Considering replacing intake manifold bank 1 myself... thoughts?
    By gdallas in forum Audi A4 - B8 Forum - 2008 - 2015
    Replies: 0
    Last Post: 22-02-2013, 09:45 AM
  3. Question intake manifold pressure
    By geo_855 in forum Audi A4 - B5 Forum - 1995 - 2002
    Replies: 0
    Last Post: 04-04-2011, 12:47 PM
  4. Intake Manifold ???
    By Bandooli in forum Golf MK4 - 1999 - 2004
    Replies: 0
    Last Post: 13-05-2008, 11:50 PM
  5. I cleaned my intake manifold - does it look right?
    By jshodgson in forum Audi A4 - B5 Forum - 1995 - 2002
    Replies: 4
    Last Post: 11-02-2008, 10:21 AM
Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


 



  


Disclaimer: VW Audi Forum is an "independant enthusiast website", administered in line with guidelines supplied by VAG in the UK, and is in no way related to any of the Worldwide Volkswagen,Audi,Seat,Skoda,Bentley,Bugatti,Porsche or Lamborghini group of Companies. For official up to date information on any of there vehicles, please visit the official websites. Any comments made throughout this website, are the views of the respective poster, and in no way represent the views of the VW Audi Forum Administration, or the worldwide Volkswagen & Audi Group of companies.


VW Audi Forum do not vet and are not responsible for any information which is posted in this forum. All content is viewed and used by you at your own risk and we do not warrant the accuracy or reliability of any of the information.


Copyright: Certain "words", "phrases" and "Images" used on this website by the Administration are "Copyright" of Volkswagen GB, Volkswagen AG (Germany), Audi GB, Audi AG (Germany), Volkswagen Motorsport GB, Volkswagen Motorsport AG (Germany), Audi Motorsport AG (Germany), Volkswagen Racing GB, Bentley, Bugatti, Porsche and Lamborghini. No image can be replicated by anyone WITHOUT the relevant Companies written permission.


All trademarks and copyrights remain property of their respective owners.

No part of the VW Audi Forum website or forum may be reproduced without written permission from the site administration


PLEASE NOTE - PERSONAL ABUSE, ABUSE AGAINST THIS OR ANY OTHER WEBSITE OR ANY COMPANY WILL NOT BE TOLERATED. OFFENDERS WILL BE MODERATED OR EVEN BANNED.


This website and forum are best viewed at a minimum resolution of 1024 by 768.



  



- VW AUDI Forum - The #1 Volkswagen (VW) Group Forum - Volkswagen (VW) - Audi - Seat - Skoda - Bentley - Bugatti - Lamborghini - Porsche - Scania - MAN - Ducatti - VW Audi Forum -


- www.vwaudiforum.co.uk - www.vwaudiforum.co.uk -