B9 VCDS Coding?

Anyone know of anything interesting yet?

Would love to invert the stop/start button as per my A6 but coding isn't the same.

Cheers


Sent from my iPad using Tapatalk

Found some coding here; the Stop/Start one appears to work on the B9.

Elektronica & Diagnose: My Tweaks A4 (B9)

HTH

I got a few from here.
Q7 (4M) Coding

I have done these:
Need sweep - Completely useless and cool as **** :)
Default distance setting for Adaptive cruise control.
Beep on lock (mine is set to 1 for unlock, 2 for lock and increased to 60ms)
Turn the volume on the soundacktor to zero.. It doesn't sound like a real engine anyway, so I might as well enjoy the quiet :)
Enable & Pair a Second Phone via Bluetooth simultaneously (I have no Audi phone box)
Increase time required to open trunk lid with remote key (now set at 2 secs - this has stopped a few mistaken openings)

Was the soundaktor changed in VCDS following:

Select Control Module
A9- Struct. Borne Sound
Adaptation - 10
Set Channel to Volume of structure-borne noise actuator
Change Stored Value to 0.0 to disable
Click "Do It"
Click "Yes" on VCDS Adaptation Warning

I cannot access A9 so I'm assuming the soundaktor isn't installed on my A5. Here's a list of changes I've made so far:

Gauge Test/Needle Sweep
[17 Instruments] > Coding-07 > Long Coding Helper > Byte 1 > Enable Bit 0
--------------------------------
DRL option in MIB:
[09 Central Electrics] > Coding-07 > Long Coding Helper > Byte 2 > Enable Bit 1
--------------------------------
Acoustic Lock/unlock:
[46-Central Module] > Coding-07 > Long Coding Helper > Byte 4 > Enable Bit 6

[ 46-Central Module ] > Adaptation - 10 > ENG146368-ENG146488-central_locking_system-beep_at_opening > activate

Configure these channels as desired:
Lock sounds: ENG146372-ENG146515-horn_settings-number_of_acoustic_acknowlagement_signals_zv_close (default 1 beep)
Unlock sounds: ENG146372-ENG146514-horn_settings-number_of_acoustic_acknowlagement_signals_zv_open (default 2 beeps)

My car was already set with the corresponding number of hazard blinks to mack the sound, so I've left as default.
--------------------------------

Here are a couple of helpful resources:

***Official*** B9 A5/S5/RS5 OBDEleven Coding Thread (Updated 8/6/2018) - AudiWorld Forums

Complete VCDS - Vagcom mod list | Audi A5 Forum & Audi S5 Forum

Does anyone know how to do the following:

1. disable the 'passenger air bag on' warning/chime that is displayed every time the car is started
2. disable the 'engine running' warning/chime every time the drivers door is opened

Here are a few more changes I've made to my B9

--------------------------------
Comfort Blinking:
[46-Central Module] > [Adaptation-10] > Turn Signal Control > Freeway Flashing Cycles > Current Value: 3 > New Value: 5 (1-5 possible)
--------------------------------
Increase time required to open boot with remote:
[46 - Central Convenience] > [Adaptation - 10] > IDE08400-Actuation time to open rear lid with remote control > Current Value: 800 (ms) > New Value: 2000 > Do it
--------------------------------
Windows Open/Close with Fob:
[46-Cent. Conv] > [Coding] > [Long Coding Helper] > Allow Experimental Data > Byte 12 > Bit 0 = Comfort_operation > active
--------------------------------
Enable Rear DRLs:
[09-Central Elec] > [Coding-07] > [Long Coding Helper] > Allow Experimental Data > Byte 2 > Bit 3 = sl_at_drl
--------------------------------
Flashing Tail Lights with Emergency Brake:
[46-Central Conv] > [Coding-07] > [Long Coding Helper] > Allow Experimental Data > Byte 21 > Bit 0 = Emergency_brake_indication_active
--------------------------------
Hazards Flashing with Emergency Stop:
[46-Central Conv] > [Coding-07] > [Long Coding Helper] > Allow Experimental Data > Byte 36 > Bit 1 = Emergency_stop_hazard_flashing_active
--------------------------------
Engine Running Warning Off:
[17-Instruments] > [Adaptation-10] > IDE06588-Ignition active message: actuator > changed from 'Driver Door' to 'No Display' this only turns off the message with ignition no, not engine running