View Full Version : Q7 4M Rear View Camera - Retrofit
andyhud007
05-06-2018, 11:50 AM
All,
A short while ago I completed a second retrofit for fellow forum member Steve on his lovely Q7 S-Line in Orca Black. (First was Drivers Side Seat Memory Buttons).
This was a Rear View Camera retrofit as the car only had the parking sensors as standard and involved swapping out the rear door handle for a new handle that contains the camera, relevant connections to the MMI Unit, Power and Coding.
Install took about 3 hours to complete.
Lovely Car:
34989
New vs Old Rear Door Handle:
34990
New Rear Handle Installed and cabled in:
34991
Wire Routing:
34992
Removal of MMI Unit and Glove box and wiring into the relevant MMI Connectors:
34993
Finished Camera:
34994
34995
Cheers
Andy
Q7NewBee
05-06-2018, 12:02 PM
All,
A short while ago I completed a second retrofit for fellow forum member Steve on his lovely Q7 S-Line in Orca Black. (First was Drivers Side Seat Memory Buttons).
This was a Rear View Camera retrofit as the car only had the parking sensors as standard and involved swapping out the rear door handle for a new handle that contains the camera, relevant connections to the MMI Unit, Power and Coding.
Install took about 3 hours to complete.
Lovely Car:
34989
New vs Old Rear Door Handle:
34990
New Rear Handle Installed and cabled in:
34991
Wire Routing:
34992
Removal of MMI Unit and Glove box and wiring into the relevant MMI Connectors:
34993
Finished Camera:
34994
34995
Cheers
Andy
Great work Andy, are you able to share ball park costs for this retrofit? Thanks
Sent from my iPhone using Tapatalk
andyhud007
05-06-2018, 12:26 PM
PM'd you mate.
Andy
Mr Blake
26-09-2018, 06:22 PM
Hi Andy well happy with both job's you have done on my car a bot late on the reply but haven't been on the forum for a bit
Cheers
Steve
deutsch
14-10-2018, 08:36 PM
i have just finished fitting the camera to my 2016 Q7 4M but i am unable to find any info on coding, would anybody be able to help please
andyhud007
15-10-2018, 04:05 PM
i have just finished fitting the camera to my 2016 Q7 4M but i am unable to find any info on coding, would anybody be able to help please
PM me and we can chat
Iain Drage
21-07-2019, 04:59 PM
Andy,
Are we full 'plug and play' albeit with a few bits of trim to remove ?
Thanks muchly, Iain
andyhud007
21-07-2019, 05:11 PM
Andy,
Are we full 'plug and play' albeit with a few bits of trim to remove ?
Thanks muchly, IainNearly Iain. Little bit of wiring and a little bit of coding but generally.. Yes
Iain Drage
21-07-2019, 10:15 PM
want to pm me a few prices tomorrow eve please
andyhud007
23-07-2019, 09:53 AM
want to pm me a few prices tomorrow eve pleaseWill drop you an email Iain.
Andy
jimbo9000
24-01-2022, 11:55 PM
Hi, thanks for this insight. I'm looking to do the same but haven't found a reasonable guide on the boot trim removal/cable laying along with connection to the relevant box in MMI. Is there a guide you would recommend on this please? Thank you.
marcinmm
07-06-2022, 04:35 PM
Rear camera coding - Is it ok?
Module 19 Gateway
Select Installation List
Check 6C Rear View Camera
Save
Module 09 Central Electrics
Select Coding
Go to Byte 35 and check Bit 4
Exit and Do it!
Module 5F Multimedia
Select Adaptation
Search for VPS
Car_Funktion_List_BAP_Gen2_VPS set the new value activated and press Do it!
Car_Funktion_List_BAP_Gen2_VPS_msg_bus set the new value Terminal 15 and press Do it!
VAG-Abound
07-06-2022, 08:57 PM
Whatever that bit does may somewhere else in different control module versions, so you should make sure it looks like the right thing to be setting rather than doing it blindly:
Go to Byte 35 and check Bit 4
I can't comment on the other parts.
corino
08-01-2023, 08:52 PM
Hi Andy, where did you tap into for CAN wires? I believe this camera uses extended CAN system for communication?
ta264
08-01-2023, 09:36 PM
The easiest place I found is at the connector for the adblue control module behind the right rear luggage compartment side trim. Check out the service manual for details and wiring diagram.
If you have some of the more advanced driver assistance modules the extended canbus wire might be present behind the left side trim by the fusebox, but mine didn't.
corino
09-01-2023, 09:27 AM
Hi mate, yeah I did see that in Erwin last night, J880 Control unit for reducing agent metering system seems like has extended CAN also, much easier than tapping into GW under seat :) thanks for confirming.
Powered by vBulletin® Version 4.2.4 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.