vcds help

[solutio]

Hey, im new with this vcds system. bought it because my wipers and my horn stop working. my wipers start working full speed sometimes for 10 minutes. i cant stop them, even if i turn of the ignition and pull the fuse.
can anybody help me reading my diagnose? the car is a caddy 07
thanks


Friday,18,March,2011,16:38:22: 60804
VCDS Version: Release 10.6.0
Data version: 20100630



--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Chassis Type: 1K0
Scan: 01 03 08 09 15 16 17 19 25 42 44 46 52 56

VIN: WV1ZZZ2KZ7X050697 Mileage: 153410km/95324miles

00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: Malfunction 0010
03-ABS Brakes -- Status: Malfunction 0010
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: Malfunction 0010
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: Malfunction 0010
17-Instruments -- Status: Malfunction 0010
19-CAN Gateway -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
42-Door Elect, Driver -- Status: Malfunction 0010
44-Steering Assist -- Status: OK 0000
46-Central Conv. -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
56-Radio -- Status: Malfunction 0010

-------------------------------------------------------------------------------
Address 01: Engine ( ) Labels: None
Part No SW: 06G 997 022 A HW: 06G 906 022 A
Component: 4220 CNG 26B6 5304
Revision: --H01--- Serial number: VWZ7Z0F7143365
Coding: 0030071
Shop #: WSC 40963 222 85004
VCID: 2B5E825AF36D

1 Fault Found:
000406 - Engine Oil Temp. Sensor (G8): Implausible Signal
P0196 - 004 - No Signal/Communication - Intermittent
Readiness: 0000 0001

-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 1K0-907-379-MK70.lbl
Part No: 1K0 907 379 P
Component: ASR FRONT MK70 0105
Coding: 0017106
Shop #: WSC 35110 377 00189
VCID: 3F86C60A1715

1 Fault Found:
00668 - Supply Voltage Terminal 30
002 - Lower Limit Exceeded - Intermittent

-------------------------------------------------------------------------------
Address 08: Auto HVAC Labels: 1K0-820-047.lbl
Part No: 1K0 820 047 FJ
Component: Climatic PQ35 120 0606
Shop #: WSC 00000 000 00000
VCID: 71E2503211C1

No fault code found.

-------------------------------------------------------------------------------
Address 09: Cent. Elect. Labels: 3C0-937-049-23-M.lbl
Part No SW: 3C0 937 049 D HW: 3C0 937 049 D
Component: Bordnetz-SG H37 1002
Revision: 00H37000 Serial number: 00000006210122
Coding: 088CCF030004100000000000000000 000008FB075C
Shop #: WSC 35110 377 08192
VCID: 2A50875EFC97

Component: Fehler Lin-Slave 01

4 Faults Found:
01493 - Bulb for Blinkers; Front Left (M5)
012 - Electrical Fault in Circuit - Intermittent
Freeze Frame:
Fault Status: 00101100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 165
Mileage: 153281 km
Time Indication: 0

Freeze Frame:
ON
Voltage: 14.20 V
ON
ON
OFF
OFF
OFF

00906 - Horn (H1)
009 - Open or Short to Ground
Freeze Frame:
Fault Status: 01101001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 128
Mileage: 153281 km
Time Indication: 0

Freeze Frame:
OFF
Voltage: 9.85 V
OFF
ON
OFF
OFF
OFF

02071 - Local Databus
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 128
Mileage: 153281 km
Time Indication: 0

Freeze Frame:
OFF
Voltage: 9.80 V
OFF
ON
OFF
OFF
OFF

00153 - Windshield Wiper Motor; Driver Side (V216)
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 12
Reset counter: 128
Mileage: 153281 km
Time Indication: 0

Freeze Frame:
OFF
Voltage: 9.80 V
OFF
ON
OFF
OFF
OFF


-------------------------------------------------------------------------------
Address 15: Airbags Labels: 6Q0-909-605-VW52.lbl
Part No SW: 6Q0 909 605 AH HW: 6Q0 909 605 AH
Component: 09 AIRBAG VW52 023 2400
Revision: 04023000 Serial number: 0037TD0BK2TS
Coding: 0012345
Shop #: WSC 35110 377 00189
VCID: 7DFA7C025D99

No fault code found.

-------------------------------------------------------------------------------
Address 16: Steering wheel Labels: 1K0-953-549-MY8.lbl
Part No SW: 1K0 953 549 BC HW: 1K0 953 549 BC
Component: Lenks‰ulenmodul 636 0070
Coding: 0000012
Shop #: WSC 35110 377 08192
VCID: 74EC59266ED3

1 Fault Found:
00883 - Ignition Switch (D) Terminal S
012 - Electrical Fault in Circuit - Intermittent

-------------------------------------------------------------------------------
Address 17: Instruments Labels: 1K0-920-xxx-17.lbl
Part No: 1T0 920 862 B
Component: KOMBIINSTRUMENT VDD 0622
Coding: 0017101
Shop #: WSC 80093 222 69422
VCID: 32609F3ED447

1 Fault Found:
01299 - Diagnostic Interface for Data Bus (J533)
008 - Implausible Signal - Intermittent

-------------------------------------------------------------------------------
Address 19: CAN Gateway Labels: 1K0-907-530.lbl
Part No SW: 1K0 907 530 H HW: 1K0 907 951
Component: J533__Gateway H04 0010
Revision: H04 02 Serial number: 15070602000042
Coding: 3D0F034007007400
Shop #: WSC 35110 377 00189
VCID: 2C5C8146F663

No fault code found.

-------------------------------------------------------------------------------
Address 25: Immobilizer Labels: 1K0-920-xxx-25.lbl
Part No: 1T0 920 862 B
Component: IMMO VDD 0622
Shop #: WSC 40972 222 55038
VCID: 32609F3ED447

No fault code found.

-------------------------------------------------------------------------------
Address 42: Door Elect, Driver Labels: 1K0-959-701-MAX3.lbl
Part No SW: 1T0 959 701 E HW: 1T0 959 701 E
Component: Tuer-SG 005 0943
Coding: 0000048
Shop #: WSC 00000 000 00000
VCID: 3972A8120931

1 Fault Found:
01044 - Control Module Incorrectly Coded
005 - No or Incorrect Basic Setting / Adaptation

-------------------------------------------------------------------------------
Address 44: Steering Assist Labels: 1Kx-909-14x.lbl
Part No: 1K1 909 144 L
Component: EPS_ZFLS Kl.140 H07 1806
Shop #: WSC 35110 666 38454
VCID: 346C99262E53

No fault code found.

-------------------------------------------------------------------------------
Address 46: Central Conv. Labels: 1K0-959-433-MIN.clb
Part No: 1K0 959 433 AK
Component: KSG 0401
Coding: 00890C087F2D8405484A016010C0
Shop #: WSC 40972 222 55038
VCID: 79F2681249B1

Component: Sounder n.mounted

Component: NGS n.mounted

Component: IRUE n.mounted

No fault code found.

-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. Labels: 1K0-959-702-MIN3.lbl
Part No SW: 1T0 959 702 D HW: 1T0 959 702 D
Component: Tuer-SG 005 0929
Coding: 0000048
Shop #: WSC 35110 377 08192
VCID: 3972A8120931

No fault code found.

-------------------------------------------------------------------------------
Address 56: Radio Labels: 1K0-035-1xx-56.lbl
Part No SW: 1K0 035 186 AD HW: 1K0 035 186 AD
Component: Radio BVX 034 0046
Revision: 00034000 Serial number: VWZ1Z2G4805413
Coding: 0010400
Shop #: WSC 00000 000 00000
VCID: 68D43D56221B

3 Faults Found:
01042 - Control Module; Not Coded
000 - -
00872 - Bass Speaker Rear Left (R15)
011 - Open Circuit
00873 - Bass Speaker Rear Right (R17)
011 - Open Circuit

End ---------------------------------------------------------------------

[burkey1]

You appear to have faults in 7 modules, which is a alot. Why dont you clear all the faults and see what comes back.

Your horn and wipers are controlled via the same module (09-Cent. Elect), its quite possible you issue is common to both faults.. Find the module and have a good look at it..

[Crasher]

As has been said, clear all the codes and see what comes back. Check the horn wiring to the horn itself; it often rubs through on the bumper support bracket screw.

[solutio]

ok, thanks for the help, i appreciate it.

I already cleared all the codes and this one is the last one.

[martin1810]

What is??

[solutio]

What is??

The vcds result.

[burkey1]

You should go into (09-Cent. Elect) and complete an output test. this should test your horn and the different stages of your wiper motor.

This will allow you to narrow down the issue.

Does the car have a good battery? Are you having starting issues?

[solutio]

You should go into (09-Cent. Elect) and complete an output test. this should test your horn and the different stages of your wiper motor.

This will allow you to narrow down the issue.

Does the car have a good battery? Are you having starting issues?

yes, i had some starting problem below -20c temp. and the battery discharges easy.
this is the 09-Cent. Elect test:


Saturday,19,March,2011,10:28:35:60804
VCDS Version: Release 10.6.0
Data version: 20100630



--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 09: Cent. Elect. Labels: 3C0-937-049-23-M.lbl
Control Module Part Number: 3C0 937 049 D HW: 3C0 937 049 D
Component and/or Version: Bordnetz-SG H37 1002
Software Coding: 088CCF030004100000000000000000000008FB075C
Work Shop Code: WSC 35110 377 08192
Additional Info: Fehler Lin-Slave 01
VCID: 2A50875EFC97
4 Faults Found:

01493 - Bulb for Blinkers; Front Left (M5)
012 - Electrical Fault in Circuit - Intermittent
Freeze Frame:
Fault Status: 00101100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 165
Mileage: 153281 km
Time Indication: 0

Freeze Frame:
ON
Voltage: 14.20 V
ON
ON
OFF
OFF
OFF

00906 - Horn (H1)
009 - Open or Short to Ground
Freeze Frame:
Fault Status: 01101001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 128
Mileage: 153281 km
Time Indication: 0

Freeze Frame:
OFF
Voltage: 9.85 V
OFF
ON
OFF
OFF
OFF

02071 - Local Databus
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 128
Mileage: 153281 km
Time Indication: 0

Freeze Frame:
OFF
Voltage: 9.80 V
OFF
ON
OFF
OFF
OFF

00153 - Windshield Wiper Motor; Driver Side (V216)
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 14
Reset counter: 128
Mileage: 153281 km
Time Indication: 0

Freeze Frame:
OFF
Voltage: 9.80 V
OFF
ON
OFF
OFF
OFF

[Crasher]

That’s I one we don’t see here, a natural gas and petrol model with a BSX engine.

Anyway I think you should do as been suggested and try the horn, wipers and indicator using the central electrics output function.

[burkey1]

A poor battery might be causing the majority of the faults.
I would replace this firstly if you are finding that it is discharging easily.

Turn your ignition on and run the output test on 09. See does your horn work and your wipers through all the stages.

Just follow attached

[solutio]

As has been said, clear all the codes and see what comes back. Check the horn wiring to the horn itself; it often rubs through on the bumper support bracket screw.

I checked the horn, it was working fine when connected to 12v. and the cables looked fine.

[solutio]

That’s I one we don’t see here, a natural gas and petrol model with a BSX engine.

Anyway I think you should do as been suggested and try the horn, wipers and indicator using the central electrics output function.


I tried the horn , wipers and indicator. just indicator was working.

[solutio]

A poor battery might be causing the majority of the faults.
I would replace this firstly if you are finding that it is discharging easily.

Turn your ignition on and run the output test on 09. See does your horn work and your wipers through all the stages.

Just follow attached

I just changed the battery and then the output test. The horn and wipers was dead.
maybe is the some control module. do you know the code for the control module to the windscreen wiper and the horn for a caddy 07?

[Crasher]

No, check the horn operation using the onboard power supply output test function, this will tell you if the onboard power supply and relay are functioning. You have the tool, use it!

[burkey1]

I think what you are saying is that you have completed the output test on 09 module and you have found the horn and wipers to be non functional. Can you confirm this???

If so it appears your control wiring is OK and the fault is from the module to device(s) that are the issue. Considering you have 2 problems from this module it is most likely the module or module output wiring that is kaput!!!

[solutio]

I think what you are saying is that you have completed the output test on 09 module and you have found the horn and wipers to be non functional. Can you confirm this???

If so it appears your control wiring is OK and the fault is from the module to device(s) that are the issue. Considering you have 2 problems from this module it is most likely the module or module output wiring that is kaput!!!

Yes, I completed the output test on 09 module, the horn and wipers was not working.

Ok, then I should try to change the module. Do you know the code or name for this module, so I can order it.

Really appreciate your responses

[burkey1]

I'm not 100% sure, but I believe its the J519 module. Don’t have much info on your car.

On the golf its under the dash panel. see diag (item 12)

Maybe Crasher can confirm if this is correct and its location?

I would check this module for loose, broken or corroded wires before I condemn it though.

[Crasher]

Look at the data for Address 09, it gives you the onboard supply control units part number.

[solutio]

thank you for all the help. I will try to replace this module and tell you the result.

[martin1810]

Are you sure the coding for the central electrics module is correct. Has anyone touched any coding on the car, even by accident.

[solutio]

The problem is fixed. It was the cable between the module and the wipers that give a pulse signal. Broken somewhere. The horn and the other electronic problems had separated issue, I just had bad luck to have it the same time.
Thanks for all the help guys.

Greg